# 1.6 Checking compression – 1.6 TDI CR engine (EA189)

> Checking compression, 1.6 TDI (Cylinder head) on the VW Polo 6R: 8 steps, special tools 3220, V.A.G 1763 and V.A.G 1763/8 and 4 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/checking-compression/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 15 – Cylinder head, valve gear, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [1.5 Removing and installing vacuum pump](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-vacuum-pump/index.md)
- Next procedure: [2.1 Assembly overview – toothed belt](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/assembly-overview-toothed-belt/index.md)

Special tools and workshop equipment required

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/e5c79b0c959f3edb.webp)

- T-bar and socket, 10 mm - 3220-

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/b38daf9b8f180ed1.webp)

- Compression tester - V.A.G 1763- with adapter - V.A.G 1763/8-

**Prerequisites for check**

- Engine oil temperature min. 80°C
- Battery voltage at least 12.5 V.

**Test sequence**

- Remove engine cover panel [⇒ 3 Engine cover panel](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/81bd2dc30c8a77be.webp)

- Disconnect electrical connector from fuel pressure regulating valve - N 276- -arrow- on fuel rail.
- Start engine briefly to reduce fuel pressure in fuel rail.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/12178b4ff862d73f.webp)

- Remove all glow pin plugs using jointed spanner - 3220- [⇒ 28 – Glow plug system](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/28-glow-plug-system/).
- Screw in adapter - V.A.G 1763/8- in each place where glow plugs were and connect compression tester - V.A.G 1763-.

> **Note**
>
> Using compression tester ⇒ operating instructions.

- Have a 2nd mechanic operate starter until tester shows no further pressure increase.

| Compression pressures | bar |
| --- | --- |
| New | 25.0 … 31.0 |
| Wear limit | 19.0 |
| Maximum difference between cylinders | 5.0 |

Installation is carried out in the reverse order; note the following:

- Install glow plugs [⇒ 28 – Glow plug system](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/28-glow-plug-system/).
- Entries are stored in the event memory of the engine control unit because electrical connectors were disconnected and the
  engine was started: Read event memory in vehicle selfdiagnosis ⇒.
