# 2.1 Assembly overview – toothed belt – 1.6 TDI CR engine (EA189)

> Toothed belt – assembly overview, 1.6 TDI (Toothed belt drive) on the VW Polo 6R: tightening torques and 2 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/assembly-overview-toothed-belt/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 15 – Cylinder head, valve gear, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [1.6 Checking compression](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/checking-compression/index.md)
- Next procedure: [2.2 Removing and installing toothed belt](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-toothed-belt/index.md)

[⇒ 2.1.2 Assembly overview - toothed belt, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/assembly-overview-toothed-belt/#t187-309)

## 2.1.2 Assembly overview - toothed belt, Polo

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/afa48a0b8eb7848c.webp)

- **1** Toothed belt
  - Mark direction of rotation before removing
  - Check for wear
  - Do not kink
  - Removing, installing and tensioning [⇒ 2.2 Removing and installing toothed belt](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-toothed-belt/#t190-82).
- **2** 120 Nm + turn 90° further
  - Renew
  - Use counterhold - 3415 - to loosen and tighten.
  - Do not additionally oil or grease the threads and shoulder
  - Turning further can be done in several stages.
- **3** Crankshaft pulley
- **4** 20 Nm
- **5** Idler roller

> **Note**
>
> Renew stud for idler pulley only if damaged. Specified torque for stud: 15 Nm.

- **6** 20 Nm + turn 45° further
  - Renew
- **7** Tensioning pulley
  - Remove engine bracket in order to remove and install [⇒ 1.8.4 Removing and installing engine bracket, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-engine-bracket/#t112-82) 

> **Note**
>
> Renew stud for tensioning roller only if damaged. Specified torque for stud: 15 Nm.

- **8** 20 Nm + turn 45° further
  - Renew
- **9** Camshaft sprocket
- **10** 15 Nm
- **11** 100 Nm
- **12** Hub
  - Use counterhold - T10051- to loosen and tighten.
  - To remove, use puller - T10052-
  - Removing and installing [⇒ 3.5 Removing and installing camshaft](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-camshaft/#t210-694)
- **13** Rear toothed belt guard
- **14** 20 Nm
- **15** 10 Nm
  - Renew
- **16** Idler roller
- **17** 50 Nm + turn 90° further
- **18** Hub
  - Use counterhold - T10051- to loosen and tighten.
  - To remove, use puller - T40064-.
- **19** 95 Nm
- **20** Toothed belt pulley on high-pressure pump
- **21** 20 Nm
  - Renew
- **22** Coolant pump
  - Removing and installing [⇒ 2.2 Removing and installing coolant pump](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/removing-and-installing-coolant-pump/#t275-82)
- **23** 15 Nm
- **24** Toothed belt guard upper part
- **25** Toothed belt guard lower part
- **26** 9 Nm
- **27** 10 Nm + turn 90° further
  - Renew
- **28** Belt pulley and vibration damper
  - Can only be installed in one position, holes are offset.
- **29** 5 Nm
  - Only fitted with protective plate from ⇒ Electronic Parts Catalogue (ETKA).
- **30** Protective plate 
- **31** 40 Nm + turn 180° further
  - Renew
  - Observe tightening sequence [⇒ 1.8.4 Removing and installing engine bracket, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-engine-bracket/#t115-421) 
- **32** Engine support
  - Removing and installing [⇒ 1.8.4 Removing and installing engine bracket, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-engine-bracket/#t112-82)

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/b471ff51e32c8f54.webp)

**Lower toothed belt guard**

- Tighten bolts -arrows- to 9 Nm.

## Tightening torques on this page

### 2.1.2 Assembly overview - toothed belt, Polo [To the drawing](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/assembly-overview-toothed-belt/#2-1-2-assembly-overview-toothed-belt-polo)
| Item | Part | Torque | Notes |
| --- | --- | --- | --- |
| 2 | + turn 90° further | 120 Nm | Renew · Use counterhold - 3415 - to loosen and tighten. · Do not additionally oil or grease the threads and shoulder · Turning further can be done in several stages. |
| 4 |  | 20 Nm |  |
| 6 | + turn 45° further | 20 Nm | Renew |
| 8 | + turn 45° further | 20 Nm | Renew |
| 10 |  | 15 Nm |  |
| 11 |  | 100 Nm |  |
| 14 |  | 20 Nm |  |
| 15 |  | 10 Nm | Renew |
| 17 | + turn 90° further | 50 Nm |  |
| 19 |  | 95 Nm |  |
| 21 |  | 20 Nm | Renew |
| 23 |  | 15 Nm |  |
| 26 |  | 9 Nm |  |
| 27 | + turn 90° further | 10 Nm | Renew |
| 29 |  | 5 Nm |  |
| 31 | + turn 180° further | 40 Nm | Renew |

### 2.1.2 Assembly overview - toothed belt, Polo [To the steps](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/assembly-overview-toothed-belt/#2-1-2-assembly-overview-toothed-belt-polo)
| Step | Torque |
| --- | --- |
| Renew stud for idler pulley only if damaged. Specified torque for stud: 15 Nm. | 15 Nm |
| Renew stud for tensioning roller only if damaged. Specified torque for stud: 15 Nm. | 15 Nm |
| Tighten bolts -arrows- to 9 Nm. | 9 Nm |
