# 1.1 Assembly overview – cylinder head – 1.6 TDI CR engine (EA189)

> Cylinder head – assembly overview, 1.6 TDI on the VW Polo 6R: tightening torques and 3 drawings. Reworking diesel cylinder heads is not permissible.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/assembly-overview-cylinder-head/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 15 – Cylinder head, valve gear, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [4.5 Checking radial clearance of conrods](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/checking-radial-clearance-of-conrods/index.md)
- Next procedure: [1.2 Removing and installing cylinder head](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-cylinder-head/index.md)

> **Note**
>
> - Do not remove the plastic packing pieces for protecting the open valves until immediately before fitting cylinder head.
> - If the cylinder head is renewed, all the coolant in the system must also be renewed.
> - If there are slight cracks, max. 0.5 mm wide, re-use cylinder heads with cracks between the valve seats.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/763fac6819b0fe94.webp)

- **1** Cylinder head
  - Removing and installing [⇒ 1.2 Removing and installing cylinder head](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-cylinder-head/#t144-82).
  - After renewing, renew entire coolant 
- **2** Washer
  - For cylinder head bolt
- **3** Cylinder head bolt
  - Observe sequence when loosening and tightening [⇒ 1.2 Removing and installing cylinder head](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-cylinder-head/#t144-82).
  - Before installing, place washers in cylinder head [⇒ Item 2 (1.1 Assembly overview - cylinder head)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/assembly-overview-cylinder-head/#t142-147)
- **4** Oil pressure switch - F1-, 22 Nm
  - Identification: green
  - 0.5 bar
  - If seal is leaking, nip open and renew.
  - Checking [⇒ 3.3 Checking oil pressure and oil pressure switch](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/17-lubrication/checking-oil-pressure-and-oil-pressure-switch/#t247-642)
- **5** 20 Nm
- **6** Lifting eye
- **7** Glow pin plug, 18 Nm
- **8** Seal
  - Renew
- **9** Vacuum pump
- **10** 10 Nm
- **11** Clip
- **12** G 62
  - Radiator outlet coolant
- **13** Seal
  - Renew
- **14** 10 Nm
- **15** Coolant hose connection
- **16** Seal
  - Renew
- **17** 25 Nm
- **18** Lifting eye
- **19** Cylinder head gasket
  - Renew
  - Observe identification [⇒ 1.1 Assembly overview - cylinder head](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/assembly-overview-cylinder-head/#t143-268).
  - After renewing, renew entire coolant
- **20** Hall sender - G40-
  - For camshaft position
  - To remove or install, toothed belt must be removed from camshaft pulley, and idler roller must be loosened.
- **21** 10 Nm

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/e351a82f9379c41a.webp)

Checking cylinder head for distortion

- Use straight edge 500 mm - VAS 6075- and feeler gauge to measure cylinder head for distortion at several points.

Max. permissible distortion: 0.1 mm

> **Note**
>
> Reworking diesel cylinder heads is not permissible. 

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/d1ea8bfa87d1a7d3.webp)

**Cylinder head gasket identification**

- **1** Part number
- **2** Holes
- **3** Ignore

> **Note**
>
> - Different thicknesses of cylinder head gasket are fitted depending on the piston projection. When renewing gasket, install new gasket with same identification.
> - Piston projection at TDC must be determined when installing new pistons or a short engine [⇒ 4.1 Assembly overview - pistons and conrods](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/assembly-overview-pistons-and-conrods/#t133-197).

## Tightening torques on this page

### Torque
| Item | Part | Torque | Notes |
| --- | --- | --- | --- |
| 4 | Oil pressure switch - F1- | 22 Nm | Identification: green · 0.5 bar · If seal is leaking, nip open and renew. |
| 5 |  | 20 Nm |  |
| 7 | Glow pin plug | 18 Nm |  |
| 10 |  | 10 Nm |  |
| 14 |  | 10 Nm |  |
| 17 |  | 25 Nm |  |
| 21 |  | 10 Nm |  |
