# 1.6 Renewing crankshaft oil seal – belt pulley end – 1.6 TDI CR engine (EA189)

> VW Polo 6R (Cylinder block (pulley end)), step by step: renewing crankshaft oil seal – belt pulley end, 1.6 TDI – 14 steps and tightening torques.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/renewing-crankshaft-oil-seal-belt-pulley-end/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 13 – Crankshaft group, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [1.5 Removing and installing bracket for ancillaries](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-bracket-for-ancillaries/index.md)
- Next procedure: [1.7 Removing and installing sealing flange on pulley end](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-installing-sealing-flange-pulley-end/index.md)

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/03402228cb8b715c.webp)

Special tools and workshop equipment required

- Seal puller - 3203-
- Counter-hold tool - 3415-
- Assembly tool - T10053-
- Torque wrench (5 … 50 Nm) - V.A.G 1331- 
- Torque wrench (40 … 200 Nm) - V.A.G 1332-

**Removing**

- Remove toothed belt [⇒ 2.2 Removing and installing toothed belt](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-toothed-belt/#t190-82).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/1385199d3592d3f8.webp)

- Remove crankshaft sprocket. To do this, lock toothed belt pulley using counterhold - 3415-.
- To guide oil seal extractor - 3203-, screw central bolt by hand into crankshaft to stop.
- Unscrew inner part of oil seal extractor 2 turns (approx. 3 mm) out of outer part and lock with knurled screw.
- Oil threaded head of oil seal extractor.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/80cd056e5205d151.webp)

- Using great pressure, screw oil seal extractor as far as possible into seal.
- Loosen knurled screw and turn inner part against crankshaft until oil seal is pulled out.

**Installing**

> **Note**
>
> Do not be additionally oil or grease the oil seal sealing lip.

- Remove oil residue from crankshaft journal using clean cloth.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/88da6a0b2cb93ad4.webp)

- Place guide sleeve - T10053/1- onto crankshaft journal.
- Slide oil seal over guide sleeve onto crankshaft journal.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/5c045779245335e0.webp)

- Press oil seal in to stop using assembly tool - T10053- and centre bolt.
- Install crankshaft sprocket.
- Specified torque of new centre bolt [⇒ 2.1 Assembly overview - toothed belt](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/assembly-overview-toothed-belt/#t185-146).
- How to install and tension toothed belt [⇒ 2.2 Removing and installing toothed belt](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-toothed-belt/#t190-82).

## Tightening torques on this page

### In the steps
| Step | Torque |
| --- | --- |
| Torque wrench (5 … 50 Nm) - V.A.G 1331- | 50 Nm |
| Torque wrench (40 … 200 Nm) - V.A.G 1332- | 200 Nm |
