# 1.7 Removing and installing sealing flange on pulley end – 1.6 TDI CR engine (EA189)

> VW Polo 6R (Cylinder block (pulley end)), step by step: removing, installing sealing flange on pulley end, 1.6 TDI – 16 steps and tightening torques.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-installing-sealing-flange-pulley-end/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 13 – Crankshaft group, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [1.6 Renewing crankshaft oil seal – belt pulley end](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/renewing-crankshaft-oil-seal-belt-pulley-end/index.md)
- Next procedure: [1.8 Removing and installing engine bracket](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-engine-bracket/index.md)

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/381720344b138436.webp)

Special tools and workshop equipment required

- Counter-hold tool - 3415-
- Assembly tool - T10053-
- Torque wrench (5 … 50 Nm) - V.A.G 1331-
- Torque wrench (40 … 200 Nm) - V.A.G 1332-
- Hand drill with plastic brush
- Sealant as per ⇒ Electronic Parts Catalogue (ETKA)
- Scraper

**Removing**

- Remove toothed belt [⇒ 2.2 Removing and installing toothed belt](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-toothed-belt/#t190-82).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/1385199d3592d3f8.webp)

- Remove crankshaft sprocket. To do this, lock toothed belt pulley using counterhold - 3415-.
- Drain engine oil.
- Remove sump [⇒ 1.2 Removing and installing sump](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/17-lubrication/removing-and-installing-sump/#t228-400).
- Pull off front sealing flange.
- Remove sealing flange; if necessary, loosen by applying light blows with a rubber-headed hammer.
- Remove sealant residue from cylinder block with a flat scraper.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/1887ed541ed96f45.webp)

- Remove residual sealant from sealing flange using a plastic rotary brush (wear eye protection).
- Clean sealing surfaces. They must be free of oil and grease.

**Installing**

> **Note**
>
> - Check the expiry date of the sealant.
> - The sealing flange must be installed within 5 minutes of applying the silicone sealant.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/fb72e37ef3f0555a.webp)

- Cut off tube nozzle at forward marking (approx. 3 mm ∅ of nozzle).

> **Note**
>
> - The thickness of the sealant bead may not exceed 2 … 3 mm.
> - Otherwise excess sealant could get into the sump and block the strainer in the oil pump suction line.
> - Sealant may also not drip onto the sealing surface of the crankshaft oil seal.
> - Before applying sealant bead, cover sealing surface of oil seal with a clean cloth.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/be5d6f8cbc605a98.webp)

- Apply silicone sealant bead as shown to the clean sealing surface of sealing flange.
- Install sealing flange immediately and tighten all bolts lightly.

> **Note**
>
> When fitting sealing flange with oil seal installed use guide sleeve - T10053/1-.

- Tighten securing bolts for sealing flange to 15 Nm using alternate and diagonal sequence.
- Install crankshaft sprocket.
- Specified torque of new centre bolt.
- Install sump [⇒ 1.2 Removing and installing sump](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/17-lubrication/removing-and-installing-sump/#t228-400).

> **Note**
>
> Leave the sealant to dry for approx. 30 minutes after assembly. Only then fill with engine oil.

Installing toothed belt and adjusting valve timing [⇒ 2.2 Removing and installing toothed belt](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-toothed-belt/#t190-82).

## Tightening torques on this page

### In the steps
| Step | Torque |
| --- | --- |
| Torque wrench (5 … 50 Nm) - V.A.G 1331- | 50 Nm |
| Torque wrench (40 … 200 Nm) - V.A.G 1332- | 200 Nm |
| Tighten securing bolts for sealing flange to 15 Nm using alternate and diagonal sequence. | 15 Nm |
