# 2.3 Removing and installing sealing flange on gearbox side – 1.6 TDI CR engine (EA189)

> VW Polo 6R (Cylinder block, gearbox end), step by step: removing, installing sealing flange on gearbox side, 1.6 TDI – 40 steps and tightening torques.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-installing-sealing-flange-gearbox-side/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 13 – Crankshaft group, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [2.2 Removing and installing flywheel](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-flywheel/index.md)
- Next procedure: [3.1 Assembly overview – crankshaft](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/assembly-overview-crankshaft/index.md)

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/37372c3daf6e8015.webp)

Special tools and workshop equipment required

- Assembly tool - T10134-
- Torque wrench - V.A.G 1331-
- Tool insert 24 mm - V.A.G 1332/11-

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/b38b40629d922ece.webp)

- Depth gauge - VAS 6082-
- 3 hexagon bolts M6 x 35 mm
- 2 hexagon bolts M7 x 35 mm 

## 2.3.1 Pressing out sealing flange with sender wheel

- Remove gearbox ⇒ Rep. gr. 34; Removing and installing gearbox; Removing gearbox.
- Remove flywheel [⇒ 2 Cylinder block, gearbox end](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/588d0e466b88fd5c.webp)

- Detach intermediate plate at sealing flange and dowel pins -arrows-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/4252db28ca459ffd.webp)

- Turn crankshaft at bolt for toothed belt pulley until crankshaft is at “TDC” of cyl. 1.
- Remove sump [⇒ 1.2 Removing and installing sump](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/17-lubrication/removing-and-installing-sump/#t228-400).

> **Note**
>
> - The work procedures are depicted with engine removed to simplify explanation.
> - The procedure is identical whether the engine is installed or removed.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/5dda7e08e621cfde.webp)

- Remove engine speed sender - G28- -1- [⇒ 1.4 Removing and installing engine speed sender - G 28-](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/28-glow-plug-system/removing-and-installing-engine-speed-sender-g-28/#t551-265).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/579ef7000c990c71.webp)

- Remove bolts for sealing flange -1 … 6-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/b77b7437c32eacec.webp)

> **Note**
>
> Press sealing flange together with sender wheel from crankshaft.

- To press out, screw in 3 bolts M6x35 -arrows- alternately into sealing flange not more than ¹/2 turn at a time.
- Remove sealing flange with sender wheel.

## 2.3.2 Pressing in sealing flange with sender wheel

> **Note**
>
> - The sealing flange with a PTFE seal is equipped with a sealing lip support ring. This support serves as an assembly sleeve. Do not remove the support ring before installation.
> - Do not separate or turn the sealing flange and sender wheel after removal from packaging.
> - The sender wheel is held in its installation position on the assembly device - T10134- by a locating pin.
> - The sealing flange and seal are one unit. The unit can only be renewed together with sender wheel.
> - The assembly device - T10134- is held in its position relative to the crankshaft by a guide pin inserted into a hole in the crankshaft.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/ae06f2f08da2a5df.webp)

**Assembly tool - T10134-**

**A - Clamping surface**

**B - Hexagon nut**

**C - Assembly housing**

**D - Locating pin**

E - Hexagon socket head bolt

F - Guide pin for diesel engines (black knob)

G - Guide pin for petrol engines (red knob) 

## 2.3.3 a) Securing seal with sender wheel on assembly tool - T10134-

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/289924f9b7ebd70a.webp)

- Screw in hexagon nut -B- to just before clamping surface -A- of threaded spindle.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/cdf3ec72cb5322c1.webp)

- Clamp assembly device - T10134- in a vice on clamping surface -A- of threaded spindle.
- Press assembly housing -C- downwards until it rests against hexagon nut -B- -arrow-.
- Screw hexagon nut onto threaded spindle until inner part of assembly device and assembly housing are at same height.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/c67a40f06c4cf1cf.webp)

- Remove securing clip -arrow- from new sealing flange.

> **Note**
>
> Do not remove the sender wheel from the sealing flange or turn it.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/273b4111e86630a2.webp)

- Locating hole -A- on sender wheel -C- must align with marking
  - B- on sealing flange.
- Place sealing flange with front side downwards on a clean flat surface.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/f3b274b23668eb92.webp)

- Push sealing lip support ring -A- downwards in direction of arrow until it lies on flat surface.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/5a88c682fc12e0c7.webp)

- Upper edge of sender wheel and front edge of sealing flange must align -arrows-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/b48427055c5dc63c.webp)

- Place sealing flange with front side on assembly tool - T10134- so that locating pin -B- can be inserted in sender wheel hole
  - A-.

> **Note**
>
> Ensure sealing flange lies flat on assembly tool.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/507cae6218373ad8.webp)

- Push sealing flange and support ring for sealing lip -B- against surface of assembly tool - T10134- whilst tightening 3 knurled screws -A- so that locating pin cannot slide out of sender wheel hole.

> **Note**
>
> When installing sealing flange, ensure that sender wheel remains fixed in assembly tool.

## 2.3.4 b) Securing assembling tool - T10134- with sealing flange on crankshaft flange

- Crankshaft flange must be free of oil and grease.
- Engine positioned at TDC No. 1 cylinder 

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/2111bc38dc5ba688.webp)

- Screw hexagon nut -B- to end of threaded spindle.
- Press threaded spindle of assembly tool - T10134- in direction of arrow, until hexagon nut -B- lies against assembly housing
  - A-.
- Align flat side of assembly housing on sump side of crankcase sealing surface.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/b732e7c77a721abc.webp)

- Secure assembly tool - T10134- to crankshaft flange using hexagon socket head bolts -A-.

> **Note**
>
> Screw hexagon socket head bolts -A- into crankshaft flange (approx. 5 full turns).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/92b543ad91a4b95d.webp)

- To guide sealing flange into cylinder block, screw in 2 M7 x 35 mm bolts (or bolts of comparable length ⇒ ⇒ Electronic parts catalogue (ETKA), standard parts) -A-.

## 2.3.5 c) Bolting assembly tool - T10134- onto crankshaft flange

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/996f4ef258a8241f.webp)

- Push assembly housing -C- by hand in direction of arrow until sealing lip support ring -B- contacts crankshaft flange -A-.
- Push guide pin for diesel engines (black knob) -D- into hole in crankshaft. This ensures that the sender wheel reaches its final installation position.

> **Note**
>
> Do not insert the guide pin for petrol engines (red knob) -F- into the threaded hole of crankshaft.

- Hand-tighten both hexagon socket head bolts of assembly tool.
- Screw hexagon nut -E- onto threaded spindle by hand until it lies on assembly housing -C-.

## 2.3.6 D - Pressing sender wheel onto crankshaft flange using assembly tool - T10134-

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/6a9662dffac488d8.webp)

- Tighten hexagon nut of assembly tool - T10134- to 35 Nm using torque wrench - V.A.G 1331- and tool insert, 24 mm - V.A.G 1332/11-.

> **Note**
>
> After hexagon nut is tightened to 35 Nm, a small air gap must still be present between cylinder block and sealing flange.

## 2.3.7 e) Checking sender wheel installation position on crankshaft

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/e2c73b2ed54a9366.webp)

- Screw hexagon nut -E- to end of threaded spindle.
- Remove the two bolts -A- from cylinder block.
- Screw the three knurled screws -B- out of sealing flange.
- Remove assembly tool - T10134-.
- Remove sealing lip support ring.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/1f2922eef79aa56c.webp)

- The sender wheel is in the correct installation position on the crankshaft if a gap -a- = 0.5 mm exists between crankshaft flange -A- and sender wheel -B-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/8feb956516c7bc28.webp)

- Position depth gauge - VAS 6082- on crankcase flange.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/7f35513849e09e6c.webp)

- Measure distance between crankshaft flange -A- and sender wheel -B-.

- Specification: dimension -a- = 0.5 mm

If dimension -a- is too small:

- Re-press sender wheel [⇒ 2.3.8 f) Re-pressing sender wheel](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-installing-sealing-flange-gearbox-side/#t126-380).

If dimension -a- is attained:

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/f6f363ca1c49fa90.webp)

- Tighten bolts for sealing flange [⇒ 2.1 Assembly overview - cylinder block, gearbox end](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/assembly-overview-cylinder-block-gearbox-end/#t117-230).
- Install engine speed sender - G28- [⇒ 1.4 Removing and installing engine speed sender - G 28-](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/28-glow-plug-system/removing-and-installing-engine-speed-sender-g-28/#t551-265).
- Install sump [⇒ 1.2 Removing and installing sump](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/17-lubrication/removing-and-installing-sump/#t228-400).
- Install intermediate plate.
- Install flywheel using new bolts. Tighten securing bolts to 60 Nm + 90° further.

## 2.3.8 f) Re-pressing sender wheel

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/eda32e60f9d5f22e.webp)

- Secure assembly tool - T10134- to crankshaft flange using hexagon socket head bolts -A-.
- Hand tighten both hexagon socket head bolts.
- Push assembly tool - T10134- by hand to sealing flange.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/e2c73b2ed54a9366.webp)

- Screw hexagon nut -E- onto threaded spindle by hand until it lies on assembly housing -C-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/6a9662dffac488d8.webp)

- Tighten hexagon nut of assembly tool - T10134- to 40 Nm using torque wrench - V.A.G 1331- and tool insert, 24 mm - V.A.G 1332/11-.
- Check installation position of sender wheel on crankshaft again. [⇒ 2.3.7 e) Checking sender wheel installation position on crankshaft](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-installing-sealing-flange-gearbox-side/#t125-283)

If dimension -a- is still too small:

- Tighten hexagon nut for assembly tool - T10134- to 45 Nm.
- Check installation position of sender wheel on crankshaft again. [⇒ 2.3.7 e) Checking sender wheel installation position on crankshaft](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-installing-sealing-flange-gearbox-side/#t125-283) 

## Tightening torques on this page

### 2.3.6 D - Pressing sender wheel onto crankshaft flange using assembly tool - T10134- [To the steps](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-installing-sealing-flange-gearbox-side/#2-3-6-d-pressing-sender-wheel-onto-crankshaft-flange-using-a)
| Step | Torque |
| --- | --- |
| Tighten hexagon nut of assembly tool - T10134- to 35 Nm using torque wrench - V.A.G 1331- and tool insert, 24 mm - V.A.G 1332/11-. | 35 Nm |
| After hexagon nut is tightened to 35 Nm, a small air gap must still be present between cylinder block and sealing flange. | 35 Nm |

### 2.3.7 e) Checking sender wheel installation position on crankshaft [To the steps](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-installing-sealing-flange-gearbox-side/#2-3-7-e-checking-sender-wheel-installation-position-on-crank)
| Step | Torque |
| --- | --- |
| Install flywheel using new bolts. Tighten securing bolts to 60 Nm + 90° further. | 60 Nm + 90° |

### 2.3.8 f) Re-pressing sender wheel [To the steps](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-installing-sealing-flange-gearbox-side/#2-3-8-f-re-pressing-sender-wheel)
| Step | Torque |
| --- | --- |
| Tighten hexagon nut of assembly tool - T10134- to 40 Nm using torque wrench - V.A.G 1331- and tool insert, 24 mm - V.A.G 1332/11-. | 40 Nm |
| Tighten hexagon nut for assembly tool - T10134- to 45 Nm. | 45 Nm |
