# 1.2 Removing and installing poly-V belt – 1.6 TDI CR engine (EA189)

> Removing and installing poly-V belt, 1.6 TDI (Cylinder block (pulley end)) on the VW Polo 6R: 29 steps, special tool T10060 A and tightening torques.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-poly-v-belt/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 13 – Crankshaft group, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [1.1 Assembly overview – poly V-belt drive](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/assembly-overview-poly-v-belt-drive/index.md)
- Next procedure: [1.3 Removing and installing tensioner for poly V-belt](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-tensioner-for-poly-v-belt/index.md)

[⇒ 1.2.1 Removing and installing poly V-belt, poly V-belt drive without air conditioner compressor](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-poly-v-belt/#t86-646)

[⇒ 1.2.2 Removing and installing poly V-belt, poly V-belt drive with tensioning roller and air-conditioning compressor](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-poly-v-belt/#t87-376)

[⇒ 1.2.3 Removing and installing poly V-belt, poly V-belt drive with tensioning element and air-conditioning compressor](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-poly-v-belt/#t89-549)

## 1.2.1 Removing and installing poly V-belt, poly V-belt drive without air conditioner compressor

> **Note**
>
> The poly V-belt repair kit with tools contains tool -T10367- and illustrated instructions.

**Removing and installing**

- Remove noise insulation:
  Polo ⇒ General body repairs, exterior; Rep. gr. 50; Noise insulation; Assembly overview - noise insulation
- Loosen right wheel housing liner in front area.
- Cut through poly V-belt.
- Further work sequence is carried out as described in the illustrated instructions enclosed with the spare part.

Install in the reverse order of removal observing the following:

- Secure front part of right wheel housing liner again.
- Install noise insulation:
  Polo ⇒ General body repairs, exterior; Rep. gr. 50; Noise insulation; Assembly overview - noise insulation

## 1.2.2 Removing and installing poly V-belt, poly V-belt drive with tensioning roller and air-conditioning compressor

Special tools and workshop equipment required

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/35d6d5ff8c7dae62.webp)

- Torque wrench - V.A.G 1331-.

**Removing**

- Remove noise insulation:
  Polo ⇒ General body repairs, exterior; Rep. gr. 50; Noise insulation; Assembly overview - noise insulation
- Loosen right wheel housing liner in front area.

**Polo**

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/da3d1382b4b6014b.webp)

- Unscrew bolts -3, 4, 6-.
- Carefully push coolant lines -5- slightly to the side.

- To create space to remove bolt for idler roller/poly V-belt -2-.

**Continued for all vehicles**

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/1177569570d75b60.webp)

- Unscrew bolt for poly V-belt idler roller -arrow- until poly V-belt can be removed easily.
- Remove poly V-belt.

**Installing**

- Using a brush, coat guide surfaces of idler roller with lubricating paste. ⇒ Electronic Parts Catalogue (EKTA) G 052 751 A1.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/a77db34dbc81c604.webp)

- Fit poly V-belt on poly V-belt pulley:

- **1** Vibration damper
- **2** Idler roller
- **3** Alternator
- **4** Air conditioner compressor

- Now insert idler roller, with its bolt, into guide of ancillary bracket.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/ff0fd3122ecec292.webp)

Tightening sequence for poly V-belt idler roller. 

- Tighten bolt in 5 stages.

| Stage | Bolt | Specified torque/turning further angle |
| --- | --- | --- |
| 1) | -2- | Screw in by hand as far as stop • the poly V-belt is tensioned |
| 2) | -2- | turn until tensioning roller bolt reaches stop • the poly V-belt is tensioned further |
| 3) | -2- | Turn back 90° |
| 4) | -2- | 30 Nm |
| 5) | -2- | Turn 90° further |

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/1d33add1fa0475cb.webp)

- Now check, as shown in illustration, whether the end of the bolt for idler roller/poly V-belt protrudes over the running surfaces of the idler roller. Dimension -a- = approx. 2.5 mm.

This ensures that the idler roller bolt was tightened up to its end position.

**Polo**

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/2dfaa8c72d059608.webp)

- Restore coolant lines -5- to their installation position, tighten -3, 4, 6-. 8 Nm.

**Continued for all vehicles**

- Turn engine at least one turn in direction of rotation at the belt pulley/vibration damper central bolt.

> **Note**
>
> - Before installing poly V-belt, ensure that all ancillaries (alternator, air conditioner compressor) are secure.
> - When fitting the poly V-belt observe belt direction of rotation and that the belt is seated correctly in the belt pulleys.

On completing work:

- Start engine and check belt running.
- If necessary, install front right wheel housing liner.
- Install noise insulation:
  Polo ⇒ General body repairs, exterior; Rep. gr. 50; Noise insulation; Assembly overview - noise insulation

## 1.2.3 Removing and installing poly V-belt, poly V-belt drive with tensioning element and air-conditioning compressor

Special tools and workshop equipment required

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/5d9ce6308934ea7c.webp)

- Locking pin - T10060 A- 

**Removing**

- Remove noise insulation:
  Polo ⇒ General body repairs, exterior; Rep. gr. 50; Noise insulation; Assembly overview - noise insulation
- Mark the direction of travel of the poly V-belt.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/ccb165640206719f.webp)

- Swing tensioning element in direction of arrow to relieve tension on poly V-belt.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/11d8f147e5972cb6.webp)

- Align holes -arrows- and lock tensioning element in position with locking pin - T10060 A-.
- Remove poly V-belt.

**Installing**

- Install in reverse order.

> **Note**
>
> - Before installing poly V-belt, ensure that all ancillaries (alternator, air conditioner compressor) are secured tightly.
> - When fitting the poly V-belt observe belt direction of rotation and that the belt is seated correctly in the belt pulleys.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/a77db34dbc81c604.webp)

- Fit poly V-belt on pulleys.

- **1** Crankshaft
- **2** Tensioning element
- **3** Alternator
- **4** Air conditioner compressor

On completing work:

- Start engine and check belt running.

## Tightening torques on this page

### 1.2.2 Removing and installing poly V-belt, poly V-belt drive with tensioning roller and air-conditioning compressor [To the table](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-poly-v-belt/#1-2-2-removing-and-installing-poly-v-belt-poly-v-belt-drive)
| Part | Torque |
| --- | --- |
| 4) | 30 Nm |

### 1.2.2 Removing and installing poly V-belt, poly V-belt drive with tensioning roller and air-conditioning compressor [To the steps](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-poly-v-belt/#1-2-2-removing-and-installing-poly-v-belt-poly-v-belt-drive)
| Step | Torque |
| --- | --- |
| Restore coolant lines -5- to their installation position, tighten -3, 4, 6-. 8 Nm. | 8 Nm |
