# 1.5 Removing and installing bracket for ancillaries – 1.6 TDI CR engine (EA189)

> VW Polo 6R (Cylinder block (pulley end)), step by step: removing and installing bracket for ancillaries, 1.6 TDI – 13 steps and tightening torques.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-bracket-for-ancillaries/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 13 – Crankshaft group, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [1.4 Removing and installing vibration damper](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-vibration-damper/index.md)
- Next procedure: [1.6 Renewing crankshaft oil seal – belt pulley end](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/renewing-crankshaft-oil-seal-belt-pulley-end/index.md)

**Removing**

- Remove high-pressure pump [⇒ 4.2 Removing and installing high-pressure pump](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-high-pressure-pump/#t420-288).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/79ed01d8724e1190.webp)

- Remove alternator ⇒ Electrical system; Rep. gr. 27; Alternator; Removing and installing alternator.

Vehicles with air conditioning system

> **Warning**
>
> Do not open the air conditioner refrigerant circuit.

- Unbolt air conditioner compressor from ancillary bracket, then secure to lock carrier ⇒ Heating, air conditioning; Rep. gr. 87; Air conditioner compressor; Removing and installing air conditioner compressor.

**Continued for all vehicles**

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/076be4bb5fab2306.webp)

- Remove idler pulleys -1- and -2- and unscrew bolt for toothed belt guard -arrow-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/829e639b73470283.webp)

- Unscrew bolts -6…1- and remove ancillaries bracket.

**Installing**

> **Warning**
>
> Specified torque: ancillary bracket [⇒ 1.5 Removing and installing bracket for ancillaries](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-bracket-for-ancillaries/#t96-309).

Specified torque: Engine bracket [⇒ 1.8 Removing and installing engine bracket](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-engine-bracket/#t101-370).

Install in reverse order. During this procedure, observe the following:

- Note any fitted sleeves in ancillary bracket and renew missing ones if necessary.
- Renew all bolts to be tightened with torque angle.
- Tack engine bracket bolt before tightening bolts for ancillary bracket. 

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/00ba2c9af0a63aec.webp)

> **Note**
>
> Renew securing bolts for ancillary bracket.

- Install bolts as follows:

- Bolts -1- and -2- M10 x 52.
- Bolts -3- and -4- M10 x 30.
- Bolts -5- and -6- M10 x 60.
- Lifting eye bolts -A- and -B- 20 Nm.

- Tighten bolts -1 to 6- in 4 stages in the sequence shown:

| Sta ge | Bolts | Specified torque/turning further angle |
| --- | --- | --- |
| 1) | -1 … 6- | Screw in by hand as far as stop |
| 2) | -1 … 6- | 40 Nm |
| 3) | -3- and -4- | Turn 45° further |
| 4) | -1, 2, 5, 6- | Turn 90° further |

- Install high-pressure pump [⇒ 4 High-pressure pump](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/), install toothed belt and adjust valve timing [⇒ 2.2 Removing and installing toothed belt](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/15-cylinder-head-valve-gear/removing-and-installing-toothed-belt/#t190-82).
- Install alternator ⇒ Electrical system; Rep. gr. 27; Alternator; Removing and installing alternator.

- Installing high-pressure pump [⇒ 4.2 Removing and installing high-pressure pump](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-high-pressure-pump/#t420-288).
- Remove air conditioner compressor from lock carrier, then position on ancillary bracket and tighten ⇒ Heating, air conditioning; Rep. gr. 87; Air conditioner compressor; Removing and installing air conditioner compressor.
- Install alternator ⇒ Electrical system; Rep. gr. 27; Alternator; Removing and installing alternator.
- Filling/bleeding high-pressure pump/fuel system [⇒ 1.3 Filling/bleeding fuel system](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/filling-bleeding-fuel-system/#t392-82).

## Tightening torques on this page

### In the steps
| Step | Torque |
| --- | --- |
| Lifting eye bolts -A- and -B- 20 Nm. | 20 Nm |

### Torque
| Part | Torque |
| --- | --- |
| 2) | 40 Nm |
