# 4.1 Assembly overview – pistons and conrods – 1.6 TDI CR engine (EA189)

> Pistons and conrods – assembly overview, 1.6 TDI on the VW Polo 6R: 6 steps, tightening torques and 7 drawings. Oil spray jet and pressure relief valve.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/assembly-overview-pistons-and-conrods/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 13 – Crankshaft group, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [3.5 Measuring radial clearance of crankshaft](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/measuring-radial-clearance-of-crankshaft/index.md)
- Next procedure: [4.2 Removing and installing pistons](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-pistons/index.md)

> **Note**
>
> Oil spray jet and pressure relief valve [⇒ 4.3 Oil spray jets/nozzles](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/17-lubrication/oil-spray-jets-nozzles/#t260-104).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/6f11053797e13103.webp)

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/e85d11093c73be81.webp)

- **1** Retaining ring
  - Renew
- **2** Piston ring
  - compression ring
  - Offset gaps by 120°
  - Use piston ring pliers to remove and install.
  - Installation position marking: “TOP” or side with lettering towards piston crown.
  - Installation position identification: “dots or dashes marking” near -arrows-, towards piston crown
  - Measuring ring gap [⇒ 4.1 Assembly overview - pistons and conrods](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/assembly-overview-pistons-and-conrods/#t135-82)
  - Measuring ring-togroove clearance [⇒ 4.1 Assembly overview - pistons and conrods](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/assembly-overview-pistons-and-conrods/#t135-237)
- **3** Piston ring
  - compression ring
  - Offset gaps by 120°
  - Use piston ring pliers to remove and install.
  - Installation position marking: “TOP” or side with lettering towards piston crown.
  - Installation position identification: “dots or dashes marking” near -arrows-, towards piston crown
  - Measuring ring gap [⇒ 4.1 Assembly overview - pistons and conrods](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/assembly-overview-pistons-and-conrods/#t135-82)
  - Measuring ring-to-groove clearance [⇒ 4.1 Assembly overview - pistons and conrods](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/assembly-overview-pistons-and-conrods/#t135-237) 
- **4** Piston ring
  - Oil scraper ring
  - Offset gap 120° relative to lower compression ring
  - Use piston ring pliers to remove and install.
  - Installation position marking: “TOP” or side with lettering towards piston crown.
  - Installation position identification: “dots or dashes marking” near -arrows-, towards piston crown
  - Measuring ring gap [⇒ 4.1 Assembly overview - pistons and conrods](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/assembly-overview-pistons-and-conrods/#t135-82)
  - Measuring ring-to-groove clearance [⇒ 4.1 Assembly overview - pistons and conrods](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/assembly-overview-pistons-and-conrods/#t135-237)
- **5** Bolt
  - Renew
  - Oil threads and contact surface
  - 30 Nm +90°
- **6** Conrod bearing cap
  - The conrod bearing cap only fits in one position and only on the appropriate conrod due to the breaking procedure (cracking) separating the cap from the conrod.
  - Mark cylinder allocation in colour -A-.
  - Installation position: Marking -B- faces towards pulley end.
- **7** Bearing bushes
  - Fitting position [⇒ 4.1 Assembly overview - pistons and conrods](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/assembly-overview-pistons-and-conrods/#t136-82)
  - Mark used bearing shells for re-installation but not on bearing surface.
  - Renew bearing shells worn down to base layer.
  - Note version: upper bearing shell (towards piston) made of a more wear-resistant material. Identification on new bearing shells: black line on bearing surface in area of joint
  - Ensure firm seating
- **8** Bolt with pressure relief valve
  - Specified torque [⇒ 1.1 Assembly overview - sump/oil pump](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/17-lubrication/assembly-overview-sump-oil-pump/#t228-278)
- **9** Oil spray jet (for cooling of pistons)
- **10** Connecting rod
  - Renew as set only.
  - With industrially cracked conrod bearing cap
  - Separate new conrod [⇒ 4.4 Separating new conrod](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/separating-new-conrod/#t139-533)
  - Mark cylinder allocation in colour -B-.
  - Installation position: markings -A- towards belt pulley end
  - Axial clearance, wear limit: 0.37 mm
  - Measuring radial clearance [⇒ 4.5 Checking radial clearance of conrods](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/checking-radial-clearance-of-conrods/#t140-231)
- **11** Retaining ring
  - Renew
- **12** Piston pin
  - If difficult to move, heat piston to approx. 60°C.
  - Remove and install using drift - VW 222 A-.
- **13** Piston
  - With combustion chamber.
  - Mark installation position and cylinder number [⇒ 4.1 Assembly overview - pistons and conrods](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/assembly-overview-pistons-and-conrods/#t135-537).
  - Checking [⇒ 4.1 Assembly overview - pistons and conrods](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/assembly-overview-pistons-and-conrods/#t135-388)
  - Install using piston ring clamp.
  - Piston and cylinder dimensions [⇒ 4.1.1 Piston and cylinder dimensions](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/assembly-overview-pistons-and-conrods/#t136-456).
  - Measuring cylinder bore [⇒ 4.1 Assembly overview - pistons and conrods](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/assembly-overview-pistons-and-conrods/#t136-230)
  - Measuring piston projection at “TDC” [⇒ 4.3 Measuring piston projection at “TDC”](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/measuring-piston-projection-at-tdc/#t137-540)  

**Measuring piston ring gap**

- Push piston ring at right angles to cylinder wall from above down into cylinder bore to approx. 15 mm from bottom end of cylinder.
- Push in using a piston without piston rings.

| Piston ring | New mm | Wear limit mm |
| --- | --- | --- |
| 1st compression ring | 0.20 … 0.40 | 1.00 |
| 2nd compression ring | 0.20 … 0.40 | 1.00 |
| Oil scraper ring | 0.25 … 0.50 | 1.00 |

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/ee79ada2968f233e.webp)

**Measuring ring-to-groove clearance**

- Clean annular groove of piston before check.

| Piston ring | New mm | Wear limit mm |
| --- | --- | --- |
| 1st compression ring | 0.06 … 0.09 | 0.25 |
| 2nd compression ring | 0.05 … 0.08 | 0.25 |
| Oil scraper ring | 0.03 … 0.06 | 0.15 |

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/49fc096e36abe594.webp)

**Checking piston**

- Measure approx. 15 mm from lower edge, offset 90° from piston pin axis with a 75 to 100 mm external micrometer.

- Maximum deviation from nominal dimension: 0.04 mm.

Nominal dimension [⇒ 4.1.1 Piston and cylinder dimensions](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/assembly-overview-pistons-and-conrods/#t136-456)

> **Note**
>
> If piston skirt is cracked, renew piston. 

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/ab9e4dc4f24ece86.webp)

Installation position and allocation of piston to cylinder

- Arrow on piston crown points towards belt pulley end -arrows-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/0d351ff63b657ef0.webp)

Installation position of bearing shells in conrods

- Centre bearing shells on conrod and on conrod bearing cap.

- Dimension -a- = 2.5 mm 

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/dae01e671111c236.webp)

**Checking cylinder bores**

- Using cylinder gauge - VAS 6078- take measurements at 3 positions diagonally in lateral direction -A- and longitudinal direction -B-.

- Maximum deviation from nominal dimension: 0.10 mm.

Nominal dimension [⇒ 4.1.1 Piston and cylinder dimensions](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/assembly-overview-pistons-and-conrods/#t136-456)

## 4.1.1 Piston and cylinder dimensions

| Honing dimension | Piston diameter mm | Cylinder bore diameter mm |
| --- | --- | --- |
| Basic dimension | 79.4551) | 79.50 |
| • 1) Dimensions include coating (thickness 0.02 mm). The | • 1) Dimensions include coating (thickness 0.02 mm). The | • 1) Dimensions include coating (thickness 0.02 mm). The |
| coating will wear down. | coating will wear down. | coating will wear down. |

## Tightening torques on this page

### Torque
| Item | Part | Torque | Notes |
| --- | --- | --- | --- |
| 5 | Bolt | 30 Nm +90° | Renew · Oil threads and contact surface |
