# 2.1 Assembly overview – cylinder block, gearbox end – 1.6 TDI CR engine (EA189)

> VW Polo 6R, step by step: cylinder block, gearbox end – assembly overview, 1.6 TDI – 2 steps, tightening torques and 3 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/assembly-overview-cylinder-block-gearbox-end/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 13 – Crankshaft group, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [1.8 Removing and installing engine bracket](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-engine-bracket/index.md)
- Next procedure: [2.2 Removing and installing flywheel](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-flywheel/index.md)

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/cc3b187508bf5f5e.webp)

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/4a1a503e0bf4cd52.webp)

- **1** Bolt
  - Renew
  - 60 Nm +90°
- **2** Flywheel
  - Removing and installing flywheel [⇒ 2.2 Removing and installing flywheel](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-flywheel/#t117-379)
  - Offset holes make assembly possible in one position only
- **3** Sender wheel
  - For engine speed sender - G28-
  - Removing and installing [⇒ 2.3 Removing and installing sealing flange on gearbox side](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-installing-sealing-flange-gearbox-side/#t118-683)
- **4** Engine speed sender - G28-
  - Removing and installing [⇒ 1.4 Removing and installing engine speed sender - G 28-](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/28-glow-plug-system/removing-and-installing-engine-speed-sender-g-28/#t551-265)
- **5** Bolt
  - 4.5 Nm
- **6** Dowel pin
  - Qty. 2
- **7** Intermediate plate
  - Do not damage or bend when assembling.
  - Installing [⇒ 2.1 Assembly overview - cylinder block, gearbox end](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/assembly-overview-cylinder-block-gearbox-end/#t117-82)
- **8** Sealing flange with oil seal
  - Removing and installing [⇒ 2.3 Removing and installing sealing flange on gearbox side](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-installing-sealing-flange-gearbox-side/#t118-683).
  - With sender wheel for engine speed.
  - Renew complete only.
  - Do not additionally oil or grease the oil seal sealing lip.
  - Before installing, remove oil residue from crankshaft journal using a clean cloth.
  - Use support sleeve supplied when installing.
- **9** Bolt
  - Specified torque and tightening sequence [⇒ 2.1 Assembly overview - cylinder block, gearbox end](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/assembly-overview-cylinder-block-gearbox-end/#t117-230)  

**Installing intermediate plate**

- Attach intermediate plate to sealing flange -arrow at top- and push onto dowel pins -arrows at bottom-. 

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/f6f363ca1c49fa90.webp)

Sealing flange on gearbox side - specified torque and tightening sequence

- Tighten bolts in 2 stages as follows:

| Stag e | Bolts | Specified torque |
| --- | --- | --- |
| 1) | -1 … 6- | Screw in by hand as far as stop |
| 2) | -1 … 6- | In diagonal sequence and in stages; final torque 15 Nm |

## Tightening torques on this page

### Torque [To the drawing](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/assembly-overview-cylinder-block-gearbox-end/#t116-217)
| Item | Part | Torque | Notes |
| --- | --- | --- | --- |
| 1 | Bolt | 60 Nm +90° | Renew |
| 5 | Bolt | 4.5 Nm |  |

### Torque
| Part | Torque |
| --- | --- |
| 2) | In diagonal sequence and in stages; final torque 15 Nm |
