# 1.1 Removing engine – 1.6 TDI CR engine (EA189)

> Removing engine, 1.6 TDI (Removing and installing engine) on the VW Polo 6R: 40 steps, special tools 3033, 3094 and VAS 5085 and 35 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/removing-engine/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 10 – Removing and installing engine, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [3.2 Checking vacuum system](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/00-technical-data/checking-vacuum-system/index.md)
- Next procedure: [1.2 Separating engine and gearbox](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/separating-engine-and-gearbox/index.md)

[⇒ 1.1.1 Removing engine, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/removing-engine/#t14-307)

## 1.1.1 Removing engine, Polo

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/707fbdfa0fc5b3e6.webp)

Special tools and workshop equipment required

- Lifting tackle - 3033- 
- Hose clamps, up to 25 mm - 3094- (only for vehicles with manual gearbox)
- Torque wrench - V.A.G 1331-
- Torque wrench - V.A.G 1332-
- Stepladder - VAS 5085-
- Workshop hoist - VAS 6100-

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/081ae1dbb1027cc9.webp)

- Drip tray for workshop hoist - VAS 6208-

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/12d5ed9bede66924.webp)

- Pliers for spring-type clips - VAS 6362-

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/6b0e3bf978ca33da.webp)

- Transportation lock - T10403-
- Engine bung set - VAS 6122- (not shown) 

> **Note**
>
> - The battery earth must be disconnected for the remaining procedure. Check whether a coded radio is fitted. Obtain anti-theft coding if necessary.
> - The engine is removed forwards together with the gearbox.
> - All cable ties that are opened or cut through when the engine is removed must be renewed in the same position when the engine is installed.

> **Warning**
>
> Observe the following points during all installation work, in particular in the engine compartment, due to the space limitations:
>
> - Route all the various lines and electrical wiring so that they are in their original positions.
> - e.g. for fuel, hydraulics, activated charcoal filter system, coolant and refrigerant, brake fluid, vacuum.
> - Ensure that there is sufficient clearance to all moving or hot components.

**Removing**

- Remove engine cover panel [⇒ 3 Engine cover panel](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/).
- With ignition switched off, disconnect battery earth strap. ⇒ Electrical system; Rep. gr. 27; Battery; Disconnecting and connecting battery

**Polo**

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/9240bc8530ee505e.webp)

- Disconnect connector -2-.
- Unscrew bolt -1-.
- Expose vacuum hoses -arrows- and place charge pressure control solenoid valve - N75- on the engine.

**Continuation for all vehicles**

- Remove air filter housing with air mass meter and connecting pipe.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/0c3cd5de4be148f8.webp)

- Detach vacuum line -arrow- on brake servo.
- Remove noise insulation:
  Polo ⇒ General body repairs, exterior; Rep. gr. 50; Noise insulation; Assembly overview - noise insulation
- Drain coolant [⇒ 1.3 Draining and adding coolant](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/draining-and-adding-coolant/#t267-554).

Vehicles with air conditioning system

- Extract refrigerant from air conditioning system ⇒ Heating, air conditioning system; Rep. gr. 00; Repair instructions; Draining the refrigerant circuit.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/66234a557884c311.webp)

- Unbolt refrigerant lines -arrows- at condenser ⇒ Heating, air conditioning; Rep. gr. 87; Refrigerant circuit; Disconnecting and connecting refrigerant lines.

**Continuation for all vehicles**

- Remove lock carrier ⇒ General body repairs, exterior; Rep. gr. 50; Lock carrier; Removing and installing lock carrier.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/08f6e54554d26145.webp)

- Detach vacuum line -1- from vacuum pump -2-.

**Polo**

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/65073ac155362391.webp)

- Unbolt positive cable -1- at positive distributor on battery.
- Place cable on engine.
- Remove air filter housing with air mass meter and connecting pipe [⇒ 7.2.2 Removing and installing air filter housing, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-air-filter-housing/#t448-678).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/be58fc25fabf9a8d.webp)

- Disconnect connectors -arrow-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/4c05195001b08d07.webp)

- Carefully loosen engine wiring harness at its fastening points -arrows-.
- Place engine wiring harness on engine.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/46ac3547561fd0e7.webp)

- In order to ensure that vacuum hose -arrow 1- from brake servo to engine is not damaged, you must remove it ⇒ Brake systems; Rep. gr. 47; Brake servo/brake master cylinder; Assembly overview - brake servo/brake master cylinder.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/96413f12c52673b0.webp)

Pre-heater line -arrow 2- is not necessarily installed.

- Separate connectors at engine control unit [⇒ 9 Engine control unit](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/).
- Disconnect connectors.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/14d9dadb4955d450.webp)

- -1- Exhaust gas temperature sender 1 - G 235-
- -2- Exhaust gas temperature sender 3 - G 495-
- -3- Exhaust gas temperature sender 4 - G 648-
- -4- lambda probe - G 39- 

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/7d279a87cd10c9a9.webp)

- Disconnect electrical connector -2- at pressure differential sender - G 505-.
- Unscrew bolt -3- from pressure differential sender - G 505- bracket.
- Lay pressure differential sender - G 505- aside to rear together with lines.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/56964db466b71d3b.webp)

- Separate fuel supply line and return line at fuel transfer point.

The procedure for this is explained in ⇒ Rep. gr. 20; Detaching plug-in connector.

- Collect any escaping fuel.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/181e47d8d8583a57.webp)

- Using a finger, release lug from fuel pre-heater valve.
- Pull fuel pre-heater valve upwards out of coolant expansion tank guide.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/1039036cb5825db2.webp)

- Unclip fuel filter from lower part of fuel filter.
- Take fuel filter out upwards.
- Place fuel filter and fuel hoses together with fuel pre-heater valve on engine.
- Remove lower part of fuel filter ⇒ Rep. gr. 20; Fuel filter; Removing and installing fuel filter.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/2e88e75803b3c629.webp)

- Filler neck: Unclip windscreen washer system reservoir -1-.
- Filler neck: Unclip windscreen washer system reservoir -2-.

Vehicles with air conditioning system

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/4708301b8bb940b4.webp)

- During further procedure, unscrew securing bolt for refrigerant line -arrow- from air conditioner compressor ⇒ Heating, air conditioning; Rep. gr. 87; Air conditioner compressor; Removing and installing refrigerant lines from and to air conditioner compressor.
- Pull off refrigerant line at air conditioner compressor and lay it aside without kinking.

**Continued for all vehicles**

- Remove coolant expansion tank and lay down on engine.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/ddfa3f21ec1ae5d5.webp)

- Unscrew bolt -arrow- (attached), unscrew intake hose -A- clockwise out of its bracket and remove.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/f922315837576ac0.webp)

- Disconnect coolant hoses from heat exchanger for heater. Lift retaining clips -1, 2- to do this.

Vehicles with dual clutch gearbox:

- Remove selector mechanism from gearbox ⇒ Rep. gr. 34; Selector mechanism; Removing and installing selector mechanism.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/1546a4dcd644238d.webp)

- Release catch on mechatronic connector by pulling -arrowand pull connector off.

Vehicles with manual gearbox:

- Remove selector mechanism from gearbox ⇒ Rep. gr. 34; Selector mechanism; Removing and installing selector mechanism.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/88103c00de6d7fdc.webp)

- Unscrew bolt -3-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/20003500869dca35.webp)

- Remove bolts -arrows- and lay clutch slave cylinder aside. Do not open hydraulic system.
- Guide clutch slave cylinder under strut -1-.

**Continued for all vehicles**

- Unbolt earth cable on gearbox.
- Disconnect all connectors between starter, gearbox and body.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/292a24a432776c70.webp)

- Unscrew bolt -1-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/99aa6fca7a9471d4.webp)

- Detach connector from oil level and oil temperature sender - G266-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/09bb1d7ed734b55c.webp)

- Remove right drive shaft cover.
- Remove drive shafts from gearbox ⇒ Running gear, axles, steering; Rep. gr. 40; Drive shaft; Removing and installing drive shaft.
- Raise and tie drive shafts as high as possible.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/8f14377913fa60b4.webp)

- Remove bolts -2…3-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/e745c6db0e4a93ad.webp)

- Remove securing clamp -1- between particulate filter and turbocharger.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/6e2c04f21eda8026.webp)

- If necessary, securing clamp -2- between particulate filter and turbocharger must also be removed from above.

**Polo**

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/1de285d9debd26d2.webp)

- Unscrew bolts -1- and nuts -2-.
- Remove particulate filter bracket.

**Continued for all vehicles**

- Push particulate filter aside and fix it in position on plenum chamber bulkhead using suitable means.

> **Note**
>
> Check that all hose and line connections between engine, gearbox and body have been detached.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/582e534eaffe3cd8.webp)

- Use lifting tackle - 3033- and workshop hoist - VAS 6100- to support »engine/gearbox assembly« in installation position.

Vibration damper end:

- Item 2.

Flywheel end:

- Item 8.

**Polo**

Remove complete engine assembly mounting [⇒ 2.1.3 Removing and installing assembly mountings](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/assembly-overview-assembly-mountings/#t69-476).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/a1ee726478e2ac28.webp)

- Unscrew nut -1- and expose earth line

Remove assembly mounting at gearbox.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/d4d378711f17bfdb.webp)

- To do this, unscrew bolts -arrows- for support arm of engine mounting.

**Continued for all vehicles**

> **Note**
>
> Carefully guide »engine/gearbox assembly« when removing to avoid damage to body.

- Slightly lift »engine/gearbox assembly« and remove forwards.

Secure engine on engine and gearbox support - VAS 6095- to carry out repairs [⇒ 1.3 Securing engine on engine and gearbox support](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/securing-engine-on-engine-and-gearbox-support/#t56-231).
