# 1.4 Installing engine – 1.6 TDI CR engine (EA189)

> Installing engine, 1.6 TDI (Removing and installing engine) on the VW Polo 6R: 40 steps, tightening torques and 8 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/installing-engine/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 10 – Removing and installing engine, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [1.3 Securing engine on engine and gearbox support](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/securing-engine-on-engine-and-gearbox-support/index.md)
- Next procedure: [2.1 Assembly overview – assembly mountings](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/assembly-overview-assembly-mountings/index.md)

[⇒ 1.4.1 Notes on installing, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/installing-engine/#t57-365)

[⇒ 1.4.3 Installing engine](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/installing-engine/#t61-82)

## 1.4.1 Notes on installing, Polo

> **Caution**
>
> When installing a new short engine, it is compulsory to fix and tighten the clamping jaws of the injectors with the specified torque after installing the high-pressure lines [⇒ Item 20 (1.2.1 Assembly overview - fuel system, Polo)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/assembly-overview-fuel-system/#t383-353). Clamping jaws are only secured »handtight« for setting the injectors while installing high-pressure lines. Non-observance of these notes may lead to damage to engine.

Installation is performed in the reverse sequence. During this procedure, observe the following:

Repairing clutch: ⇒ Rep. gr. 30; Clutch mechanism; Fitting location overview - clutch mechanism

- Check whether dowel sleeves for centring engine/gearbox have been fitted in cylinder block, insert if necessary.
- When installing »engine/gearbox assembly«, ensure sufficient clearance to subframe and radiator.

**Polo**

Torque settings: [⇒ 2.1.2 Assembly overview – assembly mountings, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/assembly-overview-assembly-mountings/#t68-82)

Electrical connections and routing ⇒ Electrical system; Rep. gr. 00; Repair instructions; Routing and securing wires.

Vehicles with manual gearbox:

- Install clutch slave cylinder ⇒ Rep. gr. 30; Clutch mechanism; Removing and installing clutch slave cylinder.
- Install gearbox selector mechanism and adjust if necessary ⇒ Rep. gr. 34; Manual gearbox; Removing and installing manual gearbox.

Vehicles with dual clutch gearbox:

- Install selector lever cable and adjust if necessary ⇒ Rep. gr. 34; Selector mechanism; Removing and installing selector mechanism.

**Continued for all vehicles**

> **Note**
>
> - After working on particulate filter, ensure it is installed free of stress.
> - Renew self-locking nuts, seals, gaskets and securing clamps.
> - The further procedure must be followed in the specified sequence to ensure that the particulate filter is installed stressfree.

> **Caution**
>
> Avoid damage of flexible joint behind particulate filter. When removing and installing:
>
> - Do not allow the flexible joint to kink by more than 10°.
> - Install flexible joint so that it is not under tension.
> - Do not damage wire mesh on decoupling element.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/5ca9e54331339943.webp)

Observe sequence when installing particulate filter:

| 1) | Position particulate filter on turbo charger and loosely attach clip -1- |
| --- | --- |
| 2) | Screw bolts and nuts -2…5- in by hand • It must still be possible to move particulate filter and bracket |
| 3) | Tighten clip -1- |
| 4) | Tighten nuts and bolts -2- and -5- |
| 5) | Tighten nuts and bolts -3- and -4- |

Polo: specified torques - particulate filter [⇒ 2.1.3 Assembly overview - front exhaust pipe with particulate filter, Polo, left-hand drive](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/26-exhaust-system/assembly-overview-emission-control/#t486-231)

- Bolt drive shafts to gearbox ⇒ Running gear, axles, steering; Rep. gr. 40; Drive shaft; Removing and installing drive shaft.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/6f09177613efb255.webp)

- Install heat shield for drive shaft (right side) -1-.

Specified torque for bolts for drive shaft heat shield -1- ⇒ Running gear, axles, steering; Rep. gr. 40; Drive shaft; Removing and installing drive shaft heat shield.

- Install lock carrier ⇒ General body repairs, exterior; Rep. gr. 50; Lock carrier; Removing and installing lock carrier.
- Secure refrigerant lines to air conditioner compressor and condenser such that they are stress-free ⇒ Heating, air conditioning; Rep. gr. 87; Refrigerant circuit; Disconnecting and connecting refrigerant lines from and to condenser.
- Fill air conditioning system ⇒ Air conditioning systems with refrigerant R134a; Rep. gr. 00; Working with air conditioner service station; Filling refrigerant circuit using air conditioner service station.
- Install battery and battery tray ⇒ Electrical system; Rep. gr. 27; Battery; Removing and installing battery.
- Observe notes after connecting battery ⇒ Electrical system; Rep. gr. 27; Battery; Disconnecting and reconnecting battery.
- Add coolant [⇒ 1.3.2 Filling with coolant](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/draining-and-adding-coolant/#t270-82).
- Filling fuel system [⇒ 1.3 Filling/bleeding fuel system](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/filling-bleeding-fuel-system/#t392-82).
- Read event memories of all control units.
- Clear all entries which may have occurred during installation ⇒ Vehicle diagnostic tester.
- Check headlight adjustment and correct if necessary ⇒ Maintenance; Booklet 20.1.

**Specified torques**

| Bolted connection | Specified torque |
| --- | --- |
| Nuts and bolts M6 M7 M8 M10 M12 | 10 Nm |
|  | 15 Nm |
|  | 20 Nm |
|  | 40 Nm |
|  | 65 Nm[1)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/installing-engine/#t59-530) |

1) Specified torque for M 12 flange bolts: 75 Nm

## 1.4.3 Installing engine

> **Caution**
>
> When installing a new short engine, it is compulsory to fix and tighten the clamping jaws of the injectors with the specified torque after installing the high-pressure lines [⇒ Item 20 (1.2.1 Assembly overview - fuel system, Polo)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/assembly-overview-fuel-system/#t383-353). Clamping jaws are only secured »handtight« for setting the injectors while installing high-pressure lines. Non-observance of these notes may lead to damage to engine.

**Specified torques**

> **Note**
>
> - The specified torques are only valid for nuts and bolts which have been slightly greased, oiled, phosphate-treated or blackoxided.
> - Additional lubricant such as engine oil or gear oil may be used, but do not use lubricant containing graphite.
> - Do not use degreased parts.
> - Tolerance for specified torques ± 15%.

| Component | Nm |
| --- | --- |
| Bolts and nuts M6 M7 M8 M10 M12 | 10 |
|  | 15 |
|  | 20 |
|  | 40 |
|  | 65 |
| Except for the following: |  |
| Drive shaft heat shield to cylinder block | 35 |

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/3dae21c92cde56f5.webp)

**Gearbox to engine attachments**

| Item | Bolt | Nm |
| --- | --- | --- |
| 1 | M12 x 55 | 80 |
| 21) | M12 x 150 | 80 |
| 3 | M10 x 50 | 40 |
| 4 | M12 x 60 | 80 |
| 52) | M6 x 8 | 10 |
| A | Dowel sleeves for centring | Dowel sleeves for centring |
| • 1) Also secures starter | • 1) Also secures starter | • 1) Also secures starter |
| • 2) Cover plate for flywheel | • 2) Cover plate for flywheel | • 2) Cover plate for flywheel |

Installation is carried out in the reverse order. When installing, note the following:

- Engine/gearbox assembly mounted on engine bracket - T10012-.

> **Note**
>
> - Renew bolts tightened through an additional specified angle.
> - Renew self-locking nuts and bolts, and seals, O-rings and gaskets.
> - Hose unions and air intake pipes and hoses must be free of oil and grease before installation.
> - Secure all hose connections with the hose clips corresponding to original equipment ⇒ Electronic Parts Catalogue (ETKA).
> - All cable ties must be secured again in the same position on installation.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/b5b646765cb097e7.webp)

- Check that intermediate plate is hooked into sealing flange and pushed onto dowel sleeves -arrows-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/9651e2869bb89827.webp)

- If there are no dowel sleeves -A- in the cylinder block for centring the engine and gearbox, insert new dowel sleeves.
- If clutch release bearing is worn, renew it ⇒ Rep. gr. 30; Clutch mechanism; Repairing clutch release mechanism.
- Lightly grease gearbox input shaft splines with grease for clutch plate splines ⇒ Electronic parts catalogue (ETKA).
- Check centring of clutch plate.
- Tighten gearbox to engine.
- Guide engine/gearbox assembly into body.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/b221f948414cebce.webp)

- First screw bolts -arrows- for engine mountings into stop by hand.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/b3b4bcbd4132b03b.webp)

- First screw bolts -arrows- for gearbox mountings into stop by hand.

- Remove engine bracket - T10012- from engine.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/4200684a508cc96c.webp)

- Installing continued coolant circulation pump.
- Installing charge air pipe [⇒ 2.1 Assembly overview - charge air system](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/21-turbocharging-supercharging/assembly-overview-charge-air-system/#t361-190).
- Install intake union.
- Installing intake hoses with screw-type clips [⇒ 2.3 Assembly overview - charge-air hose connections](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/21-turbocharging-supercharging/assembly-overview-charge-air-hose-connections/#t369-82).
- Install particulate filter [⇒ 2.2 Removing and installing particulate filter](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/26-exhaust-system/removing-and-installing-particulate-filter/#t490-231).
- Install drive shafts, transverse link and coupling rod ⇒ Running gear, axles, steering; Rep. gr. 40.
- Install air conditioner compressor ⇒ Heating, air conditioning; Rep. gr. 87; Air conditioner compressor; Removing and installing air conditioner compressor.
- Install poly V-belt [⇒ 1.2 Removing and installing poly-V belt](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/13-crankshaft-group/removing-and-installing-poly-v-belt/#t86-543).
- Install starter ⇒ Electrical system; Rep. gr. 27; Starter; Removing and installing starter.
- Install wheel housing liner front parts ⇒ General body repairs, exterior; Rep. gr. 66; Wheel housing liner; Removing and installing wheel housing liner.
- Installing radiator [⇒ 4.2 Removing and installing radiator](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/removing-and-installing-radiator/#t315-142).
- Connect coolant hoses with plug-in connector to heat exchanger for heater.
- Install pressure differential sender - G 505- [⇒ 5.6 Removing and installing pressure differential sender - G505-](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-installing-pressure-differential-sender-g505/#t432-82).
- Install washer fluid reservoir filler pipe with filler neck.
- Install clutch slave cylinder ⇒ Rep. gr. 30; Clutch mechanism; Removing and installing clutch slave cylinder.
- Install cable with cable support bracket ⇒ Rep. gr. 34; Selector mechanism; Assembly overview - selector mechanism.
- Install pendulum support [⇒ 2 Assembly mountings](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/).
- Electrical connections and routing ⇒ Electrical system; Rep. gr. 00; Repair instructions; Routing and securing wires.
- Install battery mounting and battery ⇒ Electrical system; Rep. gr. 27; Battery; Removing and installing battery.
- Install and adjust windscreen wiper arms ⇒ Electrical system; Rep. gr. 92; Windscreen wiper system; Removing and installing windscreen wiper arms.
- Install air filter housing [⇒ 7.2 Removing and installing air filter housing](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/23-mixture-preparation-injection/removing-and-installing-air-filter-housing/#t447-146).
- Check oil level [⇒ 1.5.2 Checking engine oil level](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/17-lubrication/engine-oil/#t236-82).

> **Caution**
>
> Danger of destroying control units through excessive voltage.
>
> - Never use battery charging equipment for boost starting.

- Add coolant [⇒ 1.3.2 Filling with coolant](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/19-cooling/draining-and-adding-coolant/#t270-82).
- Install noise insulation:
  Polo ⇒ General body repairs, exterior; Rep. gr. 50; Noise insulation; Assembly overview - noise insulation 

## Tightening torques on this page

### 1.4.1 Notes on installing, Polo [To the table](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/installing-engine/#1-4-1-notes-on-installing-golf-golf-plus-golf-cabriolet-polo)
| Part | Torque |
| --- | --- |
| Nuts and bolts M6 M7 M8 M10 M12 | 10 Nm |

### 1.4.1 Notes on installing, Polo [To the steps](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/installing-engine/#1-4-1-notes-on-installing-golf-golf-plus-golf-cabriolet-polo)
| Step | Torque |
| --- | --- |
| 1) Specified torque for M 12 flange bolts: 75 Nm | 75 Nm |
