# 2.1 Assembly overview – assembly mountings – 1.6 TDI CR engine (EA189)

> Assembly mountings – assembly overview, 1.6 TDI on the VW Polo 6R: 18 steps, tightening torques and 12 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/assembly-overview-assembly-mountings/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 10 – Removing and installing engine, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [1.4 Installing engine](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/installing-engine/index.md)
- Next procedure: [2.2 Supporting engine in installation position](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/supporting-engine-in-installation-position/index.md)

[⇒ 2.1.2 Assembly overview – assembly mountings, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/assembly-overview-assembly-mountings/#t68-82)

## 2.1.2 Assembly overview – assembly mountings, Polo

- Removing and installing assembly mountings [⇒ 2.1.3 Removing and installing assembly mountings](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/assembly-overview-assembly-mountings/#t69-476)

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/a1c33ed78b537a3b.webp)

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/ee32b51b6b56b6b2.webp)

- **1** Engine support
- **2** Bolt
  - Specified torque and tightening sequence [⇒ 2.1.2 Assembly overview – assembly mountings, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/assembly-overview-assembly-mountings/#t69-205)
- **3** Assembly mountings
  - Removing and installing [⇒ 2.1.3 Removing and installing assembly mountings](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/assembly-overview-assembly-mountings/#t69-476)
- **4** Bolt
  - Renew
  - 20 Nm +90°
- **5** Support arm
- **6** Nut
  - May only be unscrewed to renew engine mounting -item 3-
  - Renew
  - 40 Nm +90°
- **7** Threaded pin
  - Renew
  - 30 Nm +90°
- **8** Bolt
  - Renew
  - 30 Nm +90°
- **9** Pendulum support
- **10** Bolt
  - Pendulum support to sub-frame
  - Tightening torque ⇒ Rep. gr. 40; Subframe, anti-roll bar, suspension link
- **11** Bolt
  - Pendulum support to gearbox
  - Tightening torque ⇒ Rep. gr. 40; Subframe, anti-roll bar, suspension link
- **12** Bolt
  - Gearbox mounting to body
  - Specified torque ⇒ Rep. gr. 34; Assembly mountings; Assembly overview - assembly mountings
- **13** Bolt
  - Gearbox mounting to body
  - Specified torque ⇒ Rep. gr. 34; Assembly mountings; Assembly overview - assembly mountings
- **14** Gearbox mounting
- **15** Gearbox support
- **16** Bolt
  - Gearbox support to gearbox 
  - Specified torque ⇒ Rep. gr. 34; Assembly mountings; Assembly overview - assembly mountings
- **17** Bolt
  - Gearbox support to gearbox
  - Specified torque ⇒ Rep. gr. 34; Assembly mountings; Assembly overview - assembly mountings
- **18** Bolt
  - Gearbox mounting to body
  - Specified torque ⇒ Rep. gr. 34; Assembly mountings; Assembly overview - assembly mountings 

Engine bracket - specified torques and tightening sequence

> **Note**
>
> Renew bolts which must be tightened further to a torque angle.

> **Caution**
>
> Danger of engine bracket breaking due to application of excessive torque.
>
> - Always comply with prescribed torque and tightening sequence.

- Tighten bolts in 3 stages in the sequence shown:

| Stage | Bolts | Specified torque/turning further angle |
| --- | --- | --- |
| 1) | -1 … 3- | 7 Nm |
| 2) | -1 … 3- | 40 Nm |
| 3) | -1 … 3- | Turn 180° further |

## 2.1.3 Removing and installing assembly mountings

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/659c27f39ac60b6e.webp)

**Removing**

- Pull off engine cover panel -arrows-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/0fb5bfe42a801cdb.webp)

- Disconnect connector -3-.
- Unscrew bolt -2-, place pressure differential sender - G 505- to one side.

> **Note**
>
> Disregard -item 1-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/569e1cd1902d9151.webp)

- Release fastener -arrow- and pull fuel pre-heater valve out of guide on coolant expansion tank.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/00b81f316b0bbcb6.webp)

- Unscrew bolts -arrows-.
- Disconnect electrical connector -1- for coolant shortage indicator switch - F66- and push coolant expansion tank to side.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/9a99b1ff5caca988.webp)

- Set up support bracket - 10 - 222 A- with relevant adapters and support engine in installation position [⇒ 2.2.4 Supporting engine in installation position, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/supporting-engine-in-installation-position/#t77-298).
- Attach hook of spindle - 10 - 222 A /10- to engine lifting eye.
- Pretension spindle slightly.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/e2a67b83faa8a6b4.webp)

- Unscrew nut -1- and expose earth line
- Unscrew bolts -arrows-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/e1208866090b7c03.webp)

- Unscrew bolts -arrows- and remove engine mounting together with engine bracket.

> **Warning**
>
> Risk of accident.
>
> - The nut -1- may only be unscrewed to renew the engine mounting.

**Installing**

Install in reverse order of removal, observing the following.

- Specified torques [⇒ 2.1.2 Assembly overview – assembly mountings, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/assembly-overview-assembly-mountings/#t68-82).

> **Note**
>
> If a further tightening angle is specified for certain bolts, these must be renewed.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/0f0bc9aece4b7d4d.webp)

- Place assembly mounting on longitudinal member.

- The positioning holes -arrows- must be in line; check with appropriate drill if necessary.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/e1208866090b7c03.webp)

- First screw in bolts -arrows- as far as stop by hand.
- Tighten bolts.

> **Note**
>
> Disregard -item 1-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/0d163ba047a787a0.webp)

- First screw in bolts -arrows- for support arm of engine mounting as far as stop by hand.

- Make sure support arm is not twisted when bolts are tightened.

- Tighten bolts.

> **Note**
>
> Disregard -item 1-.

## Tightening torques on this page

### 2.1.2 Assembly overview – assembly mountings, Polo [To the drawing](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/assembly-overview-assembly-mountings/#2-1-2-assembly-overview-assembly-mountings-polo)
**All items:** Renew

| Item | Part | Torque | Notes |
| --- | --- | --- | --- |
| 4 | Bolt | 20 Nm +90° |  |
| 6 | Nut | 40 Nm +90° | May only be unscrewed to renew engine mounting -item 3- |
| 7 | Threaded pin | 30 Nm +90° |  |
| 8 | Bolt | 30 Nm +90° |  |

### 2.1.2 Assembly overview – assembly mountings, Polo [To the table](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/assembly-overview-assembly-mountings/#2-1-2-assembly-overview-assembly-mountings-polo)
| Part | Torque |
| --- | --- |
| 1) | 7 Nm |
| 2) | 40 Nm |
