# 2.3 Adjusting assembly mountings – 1.6 TDI CR engine (EA189)

> Adjusting assembly mountings, 1.6 TDI on the VW Polo 6R: 24 steps. The remaining installation steps are carried out in the reverse sequence of removal.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/adjusting-assembly-mountings/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 10 – Removing and installing engine, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [2.2 Supporting engine in installation position](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/supporting-engine-in-installation-position/index.md)
- Next procedure: [3.1 Removing and installing engine cover](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/removing-and-installing-engine-cover/index.md)

> **Warning**
>
> Observe the following points during all installation work, in particular in the engine compartment, due to the space limitations:
>
> - Route lines of any kind so that the original routing can be restored.
> - Ensure that there is sufficient clearance to all moving or hot components.

- Remove engine cover panel [⇒ 3 Engine cover panel](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/).
- Remove air filter housing.

- Remove intake hose between air mass meter - G70- and intake connecting pipe.

> **Caution**
>
> Risk of irreparable damage to electronic components when disconnecting battery.
>
> - Comply with precautions when disconnecting battery.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/d8df1ac906ecfe1f.webp)

- Disconnect earth wire -arrow- from battery with ignition switched off ⇒ Electrical system; Rep. gr. 27; Battery; Disconnecting and connecting battery.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/159e65b995008398.webp)

- Remove battery and battery tray -arrows-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/0ddcd26c2f0c4e1c.webp)

- Unscrew bolt -1-.
- Push washer fluid reservoir filler pipe with filler neck -2- to side.

> **Note**
>
> - Disregard -item 3-.
> - For reasons of clarity, diagram shows installation position with removed fuel filter.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/621ceae648720830.webp)

- Free air guide hose at retainer -2-.
- Pull retainer for fuel lines off upwards -arrow- and lay to side.
- Disconnect connector -3-.
- Unscrew bolts -1-, remove retainer and lay to side.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/19d851be0defc2b1.webp)

- Loosen bolt -1-.
- Unscrew bolt -2- and nut -3-.
- Take hose retainer -4- off fuel filter, place fuel filter -7- aside (fuel hoses -5- and -6- remain connected).
- Set up support bracket - 10 - 222 A- with relevant adapters as illustrated and support engine in installation position [⇒ 2.2.4 Supporting engine in installation position, Polo](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/supporting-engine-in-installation-position/#t77-298).

> **Note**
>
> The securing bolts for the assembly mountings may only be removed if the engine is supported with support bracket - 10-222 A-. [⇒ 2 Assembly mountings](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/)

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/4438cc44ed16ce7f.webp)

- Unscrew engine mounting bolts -arrows- in succession and renew (if not already carried out on installing engine).
- First screw bolts in loosely.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/5da3cbdb9d397d36.webp)

- Renew gearbox mounting bolts -arrows- in succession (if not already carried out) and screw in hand-tight.
- First screw bolts in loosely.

**Engine mounting **

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/beb7f7d6e3c6a1ec.webp)

- Using an assembly lever between engine bracket and support arm -1-, adjust position of engine until the specifications listed below are obtained:

- There must be a distance of -a- = 13.5 mm between engine bracket -2- and right longitudinal member.
- The side of the engine bracket casting -2- must be aligned parallel to the support arm -1- (dimension -x- must be identical on both sides).

> **Note**
>
> Distance -a- = 13.5 mm can be checked with a metal rod of suitable size, or similar.

- Tighten bolts for engine mounting.

**Gearbox mounting**

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea189-16-tdi-cr/209d47aa22c1e0ff.webp)

- On the gearbox side, ensure that the edges of the support arm -2- and gearbox support -1- are parallel.

- Dimension -x- must be identical on both sides of mounting.

- Tighten bolts for gearbox mounting.

- Specified torques [⇒ 2.1 Assembly overview - assembly mountings](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/10-removing-and-installing-engine/assembly-overview-assembly-mountings/#t66-190).

The remaining installation steps are carried out in the reverse sequence of removal. During this procedure, observe the following:

- Ensure that fuel lines are tight.
- Do not interchange supply line and return line (return line blue or with blue marking, supply line black).

- Observe notes after connecting battery ⇒ Electrical system; Rep. gr. 27; Battery; Disconnecting and connecting battery.
