# 3.1 Rules for cleanliness – 1.6 TDI CR engine (EA189)

> Rules for cleanliness, 1.6 TDI (Repair notes) on the VW Polo 6R, from the VW workshop manual.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/00-technical-data/rules-for-cleanliness/
- Original document: https://cdn.polo.blue/files/16-tdi-cr-engine-cayacaybcayc-workshop-manual-2019.pdf
- 00 – Technical data, [1.6 TDI CR engine (EA189)](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/index.md)
- Previous procedure: [2.5 Safety precautions when working on exhaust system](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/00-technical-data/safety-precautions-when-working-on-exhaust-system/index.md)
- Next procedure: [3.2 Checking vacuum system](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/00-technical-data/checking-vacuum-system/index.md)

[⇒ 3.1.1 When working on fuel supply/injection system](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/00-technical-data/rules-for-cleanliness/#t12-212)

[⇒ 3.1.2 When working on turbocharger](https://catalog.polo.blue/repair-manuals/engine-1-6-tdi-cr-ea189/00-technical-data/rules-for-cleanliness/#t12-458)

## 3.1.1 When working on fuel supply/injection system

When working on fuel supply and injection system, pay careful attention to the following rules for cleanliness:

- Thoroughly clean all unions and adjacent areas before disconnecting.
- Place removed parts on a clean surface and cover them over. Use lint-free cloths only.
- Carefully cover opened components or seal them if repairs cannot be carried out immediately.
- Install only clean parts; do not remove new parts from packaging until immediately before installing. Do not use parts that have been kept unpackaged (for example in toolboxes).
- When the system is open: Do not work with compressed air. The vehicle should not be moved.
- Also ensure that no diesel fuel comes into contact with the coolant hoses. Should this occur, the hoses must be cleaned immediately. Damaged hoses must be renewed.

## 3.1.2 When working on turbocharger

> **Caution**
>
> If a mechanical fault is found on the turbocharger, e.g. a destroyed compressor impeller, just renewing the turbocharger is not enough. To avoid subsequent damage, the following work must be carried out:
>
> - Check air filter housing, air filter element and intake hoses for dirt/soiling.
> - Check the whole charge air path and charge air cooler for foreign objects. If foreign objects are found in the charge air system, the charged air routing must be cleaned and the charge air cooler must be renewed, if necessary.
> - If bearing damage is evident on the removed turbocharger, change the engine oil and filter.

When working on the turbocharger, pay careful attention to the following rules for cleanliness:

- Thoroughly clean all unions and adjacent areas before disconnecting.
- Place removed parts on a clean surface and cover them over. Use lint-free cloths only.

- Carefully cover opened components or seal them if repairs cannot be carried out immediately.
- Install only clean parts; do not remove new parts from packaging until immediately before installing. Do not use parts that have been kept unpackaged (for example in toolboxes).
- Transportation and protective packaging and sealing caps must be removed only immediately before fitting.
- When making repairs, remove oil from connection and hose ends.
- If system is open, do not work with compressed air. Do not move the vehicle.
