# 2.5 Removing and installing coolant circulation pump V50 (Polo, Touran, Golf Plus, Eos, Tiguan, Scirocco, Golf, Golf Cabriolet) – 1.4 TSI engine (EA111)

> VW Polo 6R, step by step: removing and installing coolant circulation pump V50 (Polo) – 8 steps, special tool T10007 A, tightening torques and 3 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-4-tsi-ea111/19-cooling/removing-and-installing-coolant-circulation-pump-v50/
- Original document: https://cdn.polo.blue/files/engine-CAVA-CAVD-CAVB-CAVC-CAVE-CKMA-CTHA-CTHB-CTHC-CTHD-CTHE-CTKA-CNWA-repair-manual-eng.pdf
- 19 – Cooling, [1.4 TSI engine (EA111)](https://catalog.polo.blue/repair-manuals/engine-1-4-tsi-ea111/index.md)
- Previous procedure: [2.4 Removing and installing coolant pump belt pulley (Polo, Touran, Golf Plus, Eos, Tiguan, Scirocco, Golf, Golf Cabriolet)](https://catalog.polo.blue/repair-manuals/engine-1-4-tsi-ea111/19-cooling/removing-and-installing-coolant-pump-belt-pulley/index.md)
- Next procedure: [3.3 Assembly overview – radiator/radiator fan (Polo)](https://catalog.polo.blue/repair-manuals/engine-1-4-tsi-ea111/19-cooling/assembly-overview-radiator-radiator-fan-polo/index.md)

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/b21e200d154bb068.webp)

Special tools and workshop equipment required

- Refractometer - T10007 A-
- Hose clamp pliers - VAS 6340-
- Torque wrench - V.A.G 1331-

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/f6c1d41d146c282a.webp)

- Hose clamps to 40 mm - 3093-

**Removing**

Golf Plus, Eos, Scirocco, Golf, Golf Cabriolet, Touran, Polo

- Remove noise insulation ⇒ General body repairs, exterior; Rep. gr. 50; Body - front, noise insulation.

**Tiguan**

- Depending on vehicle equipment, remove noise insulation or skid plate ⇒ General body repairs, exterior; Rep. gr. 50; Removing and installing noise insulation or skid plate.

**Continued for all vehicles**

- Seal coolant hoses with hose clamps up to 40 mm - 3093-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/86e6bdde2196957d.webp)

- Remove spring-type clips -arrows- and pull coolant hoses off.
- Pull connector -1- off and remove securing bolt -2-.
- Remove coolant circulation pump - V50- -3-.

**Installing**

Installation is carried out in the reverse order. When installing, note the following:

Specified torque for securing bolt: 10 Nm.

- Check coolant level; replenish as necessary (Golf Plus, Eos, Scirocco, Golf, Golf Cabriolet, Touran, Tiguan).
- Check coolant level; replenish as necessary (Polo) [⇒ 1.6 Draining and filling coolant (Polo)](https://catalog.polo.blue/repair-manuals/engine-1-4-tsi-ea111/19-cooling/draining-and-filling-coolant-polo/#t196-436).

## Tightening torques on this page

### In the steps
| Step | Torque |
| --- | --- |
| Specified torque for securing bolt: 10 Nm. | 10 Nm |
