# 3.1 Removing and installing valve timing housing (Eos, Golf Plus, Scirocco, Golf, Polo, Sharan, Golf Cabriolet) – 1.4 TSI engine (EA111)

> VW Polo 6R (Cover for timing chain), step by step: removing and installing valve timing housing (Polo, Golf) – 26 steps and tightening torques.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-4-tsi-ea111/15-cylinder-head-valve-gear/removing-and-installing-valve-timing-housing/
- Original document: https://cdn.polo.blue/files/engine-CAVA-CAVD-CAVB-CAVC-CAVE-CKMA-CTHA-CTHB-CTHC-CTHD-CTHE-CTKA-CNWA-repair-manual-eng.pdf
- 15 – Cylinder head, valve gear, [1.4 TSI engine (EA111)](https://catalog.polo.blue/repair-manuals/engine-1-4-tsi-ea111/index.md)
- Previous procedure: [2.5 Removing and installing valve stem seals](https://catalog.polo.blue/repair-manuals/engine-1-4-tsi-ea111/15-cylinder-head-valve-gear/removing-and-installing-valve-stem-seals/index.md)
- Next procedure: [4.1 Checking valve timing](https://catalog.polo.blue/repair-manuals/engine-1-4-tsi-ea111/15-cylinder-head-valve-gear/checking-valve-timing/index.md)

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/01f9d5fb49c2a090.webp)

Special tools and workshop equipment required

- Support - 10-222A-
- Adapter - 10 - 222 A /8-
- Counter-hold tool - 3415-
- Pin - 3415/1-
- Torque wrench - V.A.G 1331- 

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/e26e6702032ea748.webp)

- Torque wrench - V.A.G 1332-
- Silicone adhesive sealant - D 176 501 A1-

## 3.1.1 Removing

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/ce7c9e674b60ab23.webp)

- Lift engine cover panel at points -1- and pull it forwards in direction of -arrow-.
- Remove noise insulation.
- Remove front right wheel housing liner ⇒ General body repairs, exterior; Rep. gr. 66; Removing and installing wheel housing liner.
- Mark the direction of rotation of the poly V-belt and remove belt [⇒ 1.3 Removing and installing poly V-belt (Golf Plus, Eos, Scirocco, Golf, Touran, Polo, Sharan, Passat, Passat CC, Golf Cabriolet)](https://catalog.polo.blue/repair-manuals/engine-1-4-tsi-ea111/13-crankshaft-group/removing-and-installing-poly-v-belt/#t83-239).
- Turn crankshaft in direction of engine rotation to TDC for no. 1 cylinder [⇒ 4.1 Checking valve timing](https://catalog.polo.blue/repair-manuals/engine-1-4-tsi-ea111/15-cylinder-head-valve-gear/checking-valve-timing/#t151-190).
- Drain coolant [⇒ 1.6 Draining and filling coolant (Polo)](https://catalog.polo.blue/repair-manuals/engine-1-4-tsi-ea111/19-cooling/draining-and-filling-coolant-polo/#t196-436).
- Remove coolant pump [⇒ 2.3 Removing and installing coolant pump (Polo, Touran, Golf Plus, Eos, Tiguan, Scirocco, Golf, Golf Cabriolet)](https://catalog.polo.blue/repair-manuals/engine-1-4-tsi-ea111/19-cooling/removing-and-installing-coolant-pump/#t221-82).
- Remove banjo bolt from oil supply pipe to turbocharger.
- Remove air conditioner compressor from bracket with refrigerant lines still connected ⇒ Heating, air conditioning; Rep. gr. 87.
- Remove bracket for tensioning element and air conditioner compressor.
- Remove alternator.

**Scirocco**

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/413c475b5d29391f.webp)

- Install support device - 10 - 222 A- with adapter - 10 - 222 A /8- as shown and hook into lifting eye.
- Position adapter - 10 - 222 A /8- on vehicle front end -arrows- as shown.

**All vehicles **

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/131a9df6ed4bf158.webp)

- Install support device - 10 - 222 A- with adapter - 10 - 222 A /8- as shown and hook into lifting eye.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/5fe6bf0d96b2a4ec.webp)

- Take up weight of engine and remove securing bolts -arrows-.
- Remove sump [⇒ 1.3 Removing and installing sump](https://catalog.polo.blue/repair-manuals/engine-1-4-tsi-ea111/17-lubrication/removing-and-installing-sump/#t179-448).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/dde9dd2a864b3dda.webp)

- Now remove pulley securing bolt. Hold pulley with counterhold - 3415- and -3415/1-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/7c355e0d204684f5.webp)

- Remove Allen head bolts for valve timing housing and hexagon bolts indicated by -arrows-.
- Remove valve timing housing.

> **Note**
>
> Note that crankshaft bearing bush remains in sealing flange.

## 3.1.2 Installing

> **Note**
>
> - From model year 2009, a diamond coated washer is installed. The washer prevent the crankshaft from being turned when the securing bolt is tightened.
> - Install a diamond coated washer -7- when a washer was not fitted as original equipment ⇒ Electronic Parts Catalogue “ETKA”.
> - The washer is fitted -7- between the bearing bush -5- and the crankshaft sprocket.
> - Note that all contact surfaces from the securing bolt to the crankshaft sprocket must be free of oil and grease.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/db74b959363f895e.webp)

- Clean sealing surfaces carefully. They must be free of oil and grease.

- **1** Securing bolt
- **2** Crankshaft belt pulley
- **3** Diamond coated washer (clipped onto crankshaft belt pulley)
- **4** Crankshaft oil seal
- **5** Bearing bush
- **6** O-ring
- **7** Diamond coated washer

> **Note**
>
> - Timing housing is still sealed to engine with a gasket and additionally with silicone adhesive sealant - D 176 501 A1-.
> - Silicone adhesive sealant - D 176 501 A1- prevents leaks between timing housing and joints -1- and -2-.
> - Sealant spots must have a diameter of 10 mm and a thickness of approx. 1 mm.
> - Do not apply sealant until directly before the valve timing housing is fitted.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/c72f8ee2214fc12e.webp)

- Apply silicone adhesive sealant - D 176 501 A1- to joints between camshaft housing and cylinder head -1- and between cylinder head and cylinder block -2-.
- Fit new gasket onto dowel pins.
- When fitting, install two -M6x80- studs into cylinder head and cylinder block as a guide.
- Fit valve timing housing with crankshaft bearing bush simultaneously onto studs, dowel pins and crankshaft journal.
- Tighten valve timing housing securing bolts evenly and diagonally.

Ensure that valve timing housing is not canted.

Specified torque:

M6 bolt to 10 Nm

M10 bolt to 50 Nm

Eos, Golf Plus, Scirocco, Golf, Golf Cabriolet, Sharan

Align engine mountings as follows:

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/279d508696a5ee82.webp)

- There must be a distance -a- of at least 10 mm between engine support and longitudinal member (right side).
- The side surface of the engine support -2- should be located parallel to the support arm -1-.

**Polo**

- Rock engine to align engine mountings stress-free.

Install crankshaft belt pulley [⇒ 1.7 Removing and installing crankshaft pulley](https://catalog.polo.blue/repair-manuals/engine-1-4-tsi-ea111/13-crankshaft-group/removing-and-installing-crankshaft-pulley/#t91-550).

Further assembly is basically a reverse of the dismantling sequence.

## Tightening torques on this page

### 3.1.2 Installing [To the steps](https://catalog.polo.blue/repair-manuals/engine-1-4-tsi-ea111/15-cylinder-head-valve-gear/removing-and-installing-valve-timing-housing/#3-1-2-installing)
| Step | Torque |
| --- | --- |
| M6 bolt to 10 Nm | 10 Nm |
| M10 bolt to 50 Nm | 50 Nm |
