# 4.4 Removing and installing timing chain and chain drive for oil pump – 1.4 TSI engine (EA111)

> VW Polo 6R, step by step: removing and installing timing chain, oil pump chain drive – 40 steps, special tool VAS 6079, tightening torques and 30 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-4-tsi-ea111/15-cylinder-head-valve-gear/removing-and-installing-timing-chain-and-oil-pump-drive/
- Original document: https://cdn.polo.blue/files/engine-CAVA-CAVD-CAVB-CAVC-CAVE-CKMA-CTHA-CTHB-CTHC-CTHD-CTHE-CTKA-CNWA-repair-manual-eng.pdf
- 15 – Cylinder head, valve gear, [1.4 TSI engine (EA111)](https://catalog.polo.blue/repair-manuals/engine-1-4-tsi-ea111/index.md)
- Previous procedure: [4.3 Checking timing chain](https://catalog.polo.blue/repair-manuals/engine-1-4-tsi-ea111/15-cylinder-head-valve-gear/checking-timing-chain/index.md)
- Next procedure: [1 Sump, oil pump](https://catalog.polo.blue/repair-manuals/engine-1-4-tsi-ea111/17-lubrication/sump-oil-pump/index.md)

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/abbc23be1fea8f48.webp)

Special tools and workshop equipment required

- Dial gauge - VAS 6079-
- Puller - T10094 A-
- Dial gauge adapter - T10170- or dial gauge adapter - T10170 A- (observe note [⇒ 4.4 Removing and installing timing chain and chain drive for oil pump](https://catalog.polo.blue/repair-manuals/engine-1-4-tsi-ea111/15-cylinder-head-valve-gear/removing-and-installing-timing-chain-and-oil-pump-drive/#t170-180) ).
- Camshaft clamp - T10171 A-
- Counter-hold tool - T10172-
- Pin - T40011-

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/b60bcbbf641a95df.webp)

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/0b72784a4144c902.webp)

- Spark plug socket - 3122 B-
- Counter-hold tool - 3415-
- Torque wrench - V.A.G 1331-

**Removing**

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/ce7c9e674b60ab23.webp)

- Lift engine cover panel at points -1- and pull it forwards in direction of -arrow-.
- Remove air filter (Golf, Golf Plus, Eos, Scirocco, Touran, Tiguan, Sharan, Passat, Passat CC, Golf Cabriolet) [⇒ 1.3 Removing and installing air filter housing](https://catalog.polo.blue/repair-manuals/engine-1-4-tsi-ea111/24-mixture-preparation-injection/air-filter/#t349-82).
- Drain coolant (Golf, Golf Plus, Eos, Scirocco, Touran, Tiguan, Golf Cabriolet).
- Drain coolant (Sharan).
- Drain coolant (Passat, Passat CC).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/71854aabfd1eacf6.webp)

- Remove coolant hoses and line/wiring guides -arrows-.
- Unscrew securing bolts of camshaft cover -1-.
- Remove spark plug from No. 1 cylinder. To do this, use puller
  - T10094 A- and spark plug socket and extension - 3122 B- [⇒ 1.2 Removing and installing ignition coils with output stage](https://catalog.polo.blue/repair-manuals/engine-1-4-tsi-ea111/28-ignition-system/removing-and-installing-ignition-coils-with-output-stage/#t436-722).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/34cdd74e9edf815e.webp)

- Release connector -2- and pull off.
- Remove oil pressure switch - F1- -1-.
- Then remove bolts for both camshaft covers -3-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/3c33c534fae63b73.webp)

- Unclip engine pre-wiring harness -1-.
- Pull coolant pipe -2- and engine pre-wiring harness -1- away from cylinder head.
- Remove both bolts -3- from cylinder head.

> **Note**
>
> If the dial gauge adapter - T10170 A- is used, the ball head does not need to be unscrewed from the dial gauge - VAS 6079-. The ball head is fitted onto the flat side of the rod.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/829811e4dbf8e544.webp)

- Screw dial gauge adapter - T10170- into spark plug hole to stop.
- Insert dial gauge - VAS 6079- as far as stop and lock it in position with lock nut -arrow-.
- Turn crankshaft in direction of engine rotation, to TDC No. 1 cylinder. Note position of small needle on dial gauge.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/d60682112dcebab0.webp)

The bores -arrows- in the camshafts must be as illustrated. If necessary, turn crankshaft one turn (360°) further.

> **Note**
>
> - If crankshaft is turned 0.01 mm past TDC, turn crankshaft two full turns in direction of engine rotation to set crankshaft in direction of engine rotation at TDC for No. 1 cylinder.
> - Permissible deviation from TDC No. 1 cylinder: ± 0.01 mm.

> **Caution**
>
> Before using camshaft clamp - T10171 A- you must check that the pins on the tool project by at least 7 mm.

If this is not the case, the camshaft clamp is defective and must be renewed.

Do not use any kind of hammer to position the camshaft clamp.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/b6edf537fb5854d7.webp)

- Insert camshaft clamp - T10171 A- to stop in camshaft openings.

Locking pins -arrows 1- must engage in holes -arrows 2-. Inscription “TOP” -arrow 3- must be readable from above.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/bfa40ebab8646ad0.webp)

- Screw an M6 bolt hand-tight into corresponding bore -arrows- (but do not tighten) to secure camshaft clamp - T10171 A-.

> **Note**
>
> Note that there are different securing points for the camshaft clamp - T10171 A-.

Remove valve timing housing (Eos, Golf Plus, Scirocco, Golf, Polo, Sharan, Golf Cabriolet) [⇒ 3.1 Removing and installing valve timing housing (Eos, Golf Plus, Scirocco, Golf, Polo, Sharan, Golf Cabriolet)](https://catalog.polo.blue/repair-manuals/engine-1-4-tsi-ea111/15-cylinder-head-valve-gear/removing-and-installing-valve-timing-housing/#t136-193).

Remove valve timing housing (Tiguan, Touran).

Remove valve timing housing (Passat, Passat CC)

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/8d70268a8ea8f05b.webp)

- Pull cover -1- off sprocket for oil pump.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/4517905284e85ea5.webp)

- Press tensioning rail in -direction of arrow- by hand and lock piston of chain tensioner with locking pin - T40011-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/4ad44ad3c2d024c5.webp)

- Mark direction of rotation of timing chain -3- using coloured felt tip marker pen.

> **Caution**
>
> Camshaft adjuster securing bolt -2- has a left-hand thread.

- Remove bolts -2- and -4- and remove camshaft adjuster -1- with timing chain -3-. Counterhold using counterhold - T10172-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/0e67e3f455b6a93e.webp)

- Hold oil pump sprocket with counterhold - T10172- and loosen securing bolt -1-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/8df342bfe7f1352d.webp)

- Use a screwdriver on bolt -2- to release tensioning spring -1- then remove tensioning spring -1-.
- Unscrew securing bolt -3- and remove chain tensioner.
- Mark direction of rotation of oil pump drive chain -2- using felttip marker.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/2b323caac551a80d.webp)

- Unscrew securing bolt for sprocket -1- and remove sprockets -1- and -3- together with drive chain for oil pump -2-.

**Installing**

- The crankshaft must be positioned at TDC No. 1 cylinder.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/fb6fbea63a615e4d.webp)

- Push sprocket -1- in -direction of arrow- onto crankshaft journal as far as the stop.

> **Caution**
>
> Cast lug -2- on sprocket -1- must seat in groove -3- on crankshaft journal.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/c593983ac3fa624c.webp)

- Mark position of sprocket and crankshaft to cylinder block using a felt-tip marker.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/663451b74a0d304d.webp)

- Place oil pump drive chain -3- onto sprocket -1- while positioning sprocket -2- on oil pump drive shaft.

> **Note**
>
> - Note running direction mark on oil pump drive chain.
> - Oil pump drive sprocket only fits on oil pump drive shaft in one position -arrow-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/0e67e3f455b6a93e.webp)

- Hold oil pump drive sprocket with counterhold - T10172-.
- Tighten new securing bolt -1- to 20 Nm + ¹/4 turn (90°) further.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/c259f7ddef4b0a79.webp)

- Position chain tensioner on oil pump drive chain and tighten securing bolt -3- to 8 Nm.
- Lever tensioning spring -1- onto bolt -2- using a screwdriver.

> **Note**
>
> - Note marks -arrows-.
> - The crankshaft must remain stationary.

- Tighten sprocket -3- hand-tight with new securing bolt.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/46ef98acc25692ac.webp)

- Place timing chain -1- on crankshaft sprocket -4-, exhaust camshaft sprocket -3-, and tighten camshaft adjuster -2- handtight using a new securing bolt.

> **Note**
>
> - Note running direction mark on timing chain -1-.
> - Ensure guide sleeve is installed between inlet camshaft and camshaft adjuster.
> - Camshaft adjuster securing bolt -2- has a left-hand thread.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/fc89e3f6533044b3.webp)

Timing chain must lie on guide rail -1- and crankshaft sprocket -arrow-.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/e246a5ebc7010185.webp)

- Install chain tensioner -1- and tighten securing bolts -2- to 9 Nm.
- Tension timing chain by pulling locking pin - T40011- from chain tensioner.
- Check marks on crankshaft sprocket and cylinder block; they must align.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/d74869a819f85d48.webp)

- Tighten securing bolt -2- to 40 Nm and bolt -4- to 50 Nm (use counterhold -T10172- ).

> **Note**
>
> - Securing bolts -2- and -4- are only tightened 90° further once timing has been checked.
> - The camshaft adjuster securing bolt -2- has a left-hand thread.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/bfa40ebab8646ad0.webp)

- Unscrew bolt -arrow- and remove camshaft clamp - T10171 A- from camshaft housing.
- Check valve timing [⇒ 4.1 Checking valve timing](https://catalog.polo.blue/repair-manuals/engine-1-4-tsi-ea111/15-cylinder-head-valve-gear/checking-valve-timing/#t151-190)

If valve timing is OK:

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/384d476e9a06b484.webp)

- Hold camshaft sprockets with counterhold - T10172- and tighten securing bolts -2- (left-hand thread) and -4- 1/4 turn (90°) further with a rigid wrench.

> **Note**
>
> Camshaft adjuster securing bolt -2- has a left-hand thread.

> **Note**
>
> Camshaft sprockets cannot move on camshaft whilst tightening.

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/88cd02f41c4d4f56.webp)

- Install oil pump wheel cover -1-.

Remove valve timing housing (Eos, Golf Plus, Scirocco, Golf, Polo, Sharan, Golf Cabriolet) [⇒ 3.1 Removing and installing valve timing housing (Eos, Golf Plus, Scirocco, Golf, Polo, Sharan, Golf Cabriolet)](https://catalog.polo.blue/repair-manuals/engine-1-4-tsi-ea111/15-cylinder-head-valve-gear/removing-and-installing-valve-timing-housing/#t136-193).

Remove valve timing housing (Tiguan, Touran).

Remove valve timing housing (Passat, Passat CC)

- Install crankshaft pulley [⇒ 1.7 Removing and installing crankshaft pulley](https://catalog.polo.blue/repair-manuals/engine-1-4-tsi-ea111/13-crankshaft-group/removing-and-installing-crankshaft-pulley/#t91-550).
- Install poly V-belt (Golf Plus, Eos, Scirocco, Golf, Touran, Polo, Sharan, Passat, Passat CC, Golf Cabriolet) [⇒ 1.3 Removing and installing poly V-belt (Golf Plus, Eos, Scirocco, Golf, Touran, Polo, Sharan, Passat, Passat CC, Golf Cabriolet)](https://catalog.polo.blue/repair-manuals/engine-1-4-tsi-ea111/13-crankshaft-group/removing-and-installing-poly-v-belt/#t83-239).
- Install poly V-belt (Tiguan).

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/4e3ca8332401b2d6.webp)

- Push engine cover panel down at points -1- in direction of -arrow- until it engages.

Further assembly is basically a reverse of the dismantling sequence.

**Specified torque**

| Component | Specified torque |
| --- | --- |
| Oil pressure switch - F1- | 20 Nm |

## Tightening torques on this page

### In the steps
| Step | Torque |
| --- | --- |
| Tighten new securing bolt -1- to 20 Nm + 1/4 turn (90°) further. | 20 Nm |
| Position chain tensioner on oil pump drive chain and tighten securing bolt -3- to 8 Nm. | 8 Nm |
| Install chain tensioner -1- and tighten securing bolts -2- to 9 Nm. | 9 Nm |
| Tighten securing bolt -2- to 40 Nm and bolt -4- to 50 Nm (use counterhold -T10172- ). | 40 Nm / 50 Nm |

### Torque
| Part | Torque |
| --- | --- |
| Oil pressure switch - F1- | 20 Nm |
