# 1.3 Removing and installing poly V-belt (Golf Plus, Eos, Scirocco, Golf, Touran, Polo, Sharan, Passat, Passat CC, Golf Cabriolet) – 1.4 TSI engine (EA111)

> VW Polo 6R (Cylinder block (pulley end)), step by step: removing and installing poly V-belt (Polo, Golf, Passat) – 11 steps and special tool T10060 A.

- Web page: https://catalog.polo.blue/repair-manuals/engine-1-4-tsi-ea111/13-crankshaft-group/removing-and-installing-poly-v-belt/
- Original document: https://cdn.polo.blue/files/engine-CAVA-CAVD-CAVB-CAVC-CAVE-CKMA-CTHA-CTHB-CTHC-CTHD-CTHE-CTKA-CNWA-repair-manual-eng.pdf
- 13 – Crankshaft group, [1.4 TSI engine (EA111)](https://catalog.polo.blue/repair-manuals/engine-1-4-tsi-ea111/index.md)
- Previous procedure: [1.2 Assembly overview – cylinder block, belt pulley end](https://catalog.polo.blue/repair-manuals/engine-1-4-tsi-ea111/13-crankshaft-group/assembly-overview-cylinder-block-belt-pulley-end/index.md)
- Next procedure: [1.5 Removing and installing bracket for ancillaries](https://catalog.polo.blue/repair-manuals/engine-1-4-tsi-ea111/13-crankshaft-group/removing-and-installing-bracket-for-ancillaries/index.md)

Special tools and workshop equipment required

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/6c0c7e666e7002ec.webp)

- Locking pin - T10060 A-
- 16 mm open-end spanner - T10447- (not shown)
- 4 mm Allen key

**Removing**

> **Note**
>
> The belt drive can be fitted with a tensioning element and an idler roller or with two tensioning elements.

- Remove noise insulation.
- Mark direction of rotation of poly V-belt.

**Polo only**

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/da7159e40a583a47.webp)

- Press filler neck for windscreen washer fluid out of bracket in -direction of arrow-.

**Sharan only**

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/a68ef6dd57361ceb.webp)

- Open retaining clip of refrigerant line -arrow-.

Vehicles with two tensioning elements

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/df1edd64c80567ee.webp)

- To slacken poly V-belt, swivel tensioning element in direction of -arrow- from above using 16 mm open-end spanner - T10447-.
- Lock tensioning element using locking pin - T10060 A-.

**Continued for all vehicles **

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/f9a16be8b3f2e752.webp)

- To slacken poly V-belt, swing tensioning element in direction of -arrow- from below using 16 mm open-end spanner.
- Lock tensioning element with a 4 mm Allen key -1-.
- Remove poly V-belt -2-.

**Installing**

> **Caution**
>
> Before installing poly V-belt, ensure that all ancillaries (alternator, air conditioner compressor) are secured tightly.

When installing poly V-belt, observe direction of rotation and make sure it is properly seated on pulleys and tensioning elements.

- Fit poly V-belt first over crankshaft pulley. Finally, push belt onto tensioning roller.

Further assembly is basically a reverse of the dismantling sequence.

After completing repairs:

- Start engine, and check if belt runs properly.

## 1.3.1 Poly V-belt routing

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/9dad4e549767761e.webp)

Belt drive with air conditioner compressor

- **1** Pulley - cooling system pump
- **2** Crankshaft pulley
- **3** Tensioning pulley
- **4** Tensioning roller or idler roller
- **5** Alternator pulley
- **6** Air conditioner compressor pulley
- **7** Poly V-belt

![](https://catalog.polo.blue/manuals/vw-polo-engine-ea111-14-tsi/dca2fbf7d63ff658.webp)

**Belt drive for supercharger**

> **Note**
>
> - The pulley of the magnetic clutch for supercharger - N421- is located behind the coolant pump pulley.
> - The poly V-belt -4- runs over the pulley of the magnetic clutch for supercharger - N421-.

- **1** Supercharger pulley
- **2** Tensioning pulley
- **3** Pulley - coolant pump with pulley - magnetic clutch for supercharger - N421-
- **4** Poly V-belt
