# 1.2 Right Stub Shaft Seal, Replacing – 7-speed DSG gearbox 0AM (DQ200)

> DSG 0AM right stub shaft oil seal, replacing (Seals) on the VW Polo 6R/6C: 14 steps, special tools 3305 and T10107A, tightening torques and 3 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/39-final-drive-differential/right-stub-shaft-seal-replacing/
- Original document: https://cdn.polo.blue/files/7-speed_dual_clutch_transmission_0am-eng.pdf
- 39 – Final Drive, Differential, [7-speed DSG gearbox 0AM (DQ200)](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/index.md)
- Previous procedure: [1.1 Component Location Overview – Seals](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/39-final-drive-differential/component-location-overview-seals/index.md)
- Next procedure: [1.3 Left Stub Shaft Seal, Replacing](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/39-final-drive-differential/left-stub-shaft-seal-replacing/index.md)

Left side. Refer to [⇒ 1.3 Left Stub Shaft Seal, Replacing](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/39-final-drive-differential/left-stub-shaft-seal-replacing/#t212-339).

Special tools and workshop equipment required

- Seal Installer - Flange Shaft - 3305-
- Socket And Extended Bit - T10107A- or Long Hex Socket - VAG1669-
- Used Oil Collection and Extraction Unit - SMN372500-
- Sealing Grease - G 052 128 A1- 

**Removing**

> **Note**
>
> - Do not remove both drive axles from the transmission at the same time. Then it would not be possible to hold the opposite front wheel in place in order to remove or install the stub shaft bolts.
> - Do not remove both stub shafts from the transmission at the same time. If the differential bevel gear turns in the differential then the bolts for the stub shafts are very difficult to reinstall.

- Remove the noise insulation below the engine/transmission. Refer to ⇒ Body Exterior; Rep. Gr. 50; Noise Insulation.
- Remove the drive axle. Refer to ⇒ Suspension, Wheels, Steering; Rep. Gr. 40; Drive Axles, Removing and Installing.
- Place the Used Oil Collection and Extraction Unit - SMN372500- or Drip Tray under the transmission.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/1a67563938a12b98.webp)

- Remove the bolt -arrow- in the stub shaft using the Socket And Extended Bit - T10107A- or Long Hex Socket - VAG1669-.
- Remove the stub shaft.
- Pry out the sealing ring.

**Installing**

- Lightly oil the new gasket on the outer circumference.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/15013b6c31796be9.webp)

- Fill the space between the sealing and dust lip halfway with Sealing Grease - G 052 128- -arrow-.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/80251b5b4102aea5.webp)

- Install the seal all the way in without tilting it.

If necessary, install a new dust ring on the stub shaft using Press Piece - Trailing Arm - 2010-. Do not use a hammer.

- Insert the stub shaft.
- Tighten the stub shaft bolt to 30 Nm. Push the stub shaft against the transmission so that the bolt engages in the thread.
- Reinstall the drive axle. Refer to ⇒ Suspension, Wheels, Steering; Rep. Gr. 40; Drive Axles, Removing and Installing.
- Refill any transmission fluid that may have leaked out while removing the seal. Refer to [⇒ 1 Transmission Fluid, Replacing](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/34-controls-housing/transmission-fluid-replacing/).

> **Note**
>
> The transmission fluid must be replaced to assure the transmission fluid level is correct.

- Install the noise insulation. Refer to ⇒ Body Exterior; Rep. Gr. 50; Noise Insulation.

## Tightening torques on this page

### In the steps
| Step | Torque |
| --- | --- |
| Tighten the stub shaft bolt to 30 Nm. Push the stub shaft against the transmission so that the bolt engages in the thread. | 30 Nm |
