# 1.4 Right Flange Shaft Seal, Replacing – 7-speed DSG gearbox 0AM (DQ200)

> DSG 0AM right flange shaft oil seal, replacing (Seals) on the VW Polo 6R/6C: 16 steps, special tools 3305 and T10038, tightening torques and 5 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/39-final-drive-differential/right-flange-shaft-seal-replacing/
- Original document: https://cdn.polo.blue/files/7-speed_dual_clutch_transmission_0am-eng.pdf
- 39 – Final Drive, Differential, [7-speed DSG gearbox 0AM (DQ200)](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/index.md)
- Previous procedure: [1.3 Left Stub Shaft Seal, Replacing](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/39-final-drive-differential/left-stub-shaft-seal-replacing/index.md)
- Next procedure: [1.5 Left Flange Shaft Seal, Replacing](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/39-final-drive-differential/left-flange-shaft-seal-replacing/index.md)

Left side. Refer to [⇒ 1.5 Left Flange Shaft Seal, Replacing](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/39-final-drive-differential/left-flange-shaft-seal-replacing/#t216-332).

Special tools and workshop equipment required

- Seal Installer - Flange Shaft - 3305-
- Tensioning Strap - T10038-
- Socket And Extended Bit - T10107A- or Long Hex Socket - VAG1669-
- Used Oil Collection and Extraction Unit - SMN372500-
- Sealing Grease - G 052 128 A1-

**Removing**

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/8385b1b30e49f71c.webp)

> **Note**
>
> - Do not remove both flange shafts from the transmission at the same time. If the differential bevel gear turns in the differential then the flange shaft bolts are very difficult to reinstall.
> - The drive axle must be removed from the transmission and set to the side. The drive axle is secured with the Tensioning Strap - T10038- to the suspension strut.
> - The bolt for the drive axle to wheel bearing housing connection does not need to be loosened.

- Remove the noise insulation. Refer to ⇒ Body Exterior; Rep. Gr. 50; Noise Insulation.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/306defeb6bcabc40.webp)

- If equipped, remove the drive axle heat shield from the engine -arrows-.
- Remove right drive axle from transmission flange shaft.
- Tie up the drive axle as high as possible. Do not damage the paint on the drive axle.

> **Note**
>
> - On some engines, the drive axle cannot be tied up so that the transmission flange shaft can be removed.
> - Remove the right drive axle. Refer to ⇒ Suspension, Wheels, Steering; Rep. Gr. 40; Drive Axles, Removing and Installing.

- Place the Used Oil Collection and Extraction Unit - SMN372500- or Drip Tray under the transmission.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/036089249cc1e31f.webp)

- Remove the right flange shaft bolt at the transmission using the Socket And Extended Bit - T10107A-. Insert two bolts in the flange and counterhold with a tire iron.

The bolt has 6 mm inner hex. The bolt can also be removed and installed using the Long Hex Socket - VAG1669-.

- Remove the flange shaft.
- Pry out the sealing ring.

**Installing**

- Lightly oil the new gasket on the outer circumference.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/15013b6c31796be9.webp)

- Fill the space with the new seal between the sealing and dust lip halfway with Sealing Grease - G 052 128- -arrow-.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/80251b5b4102aea5.webp)

- Drive in the new seal all the way using the Seal Installer - Flange Shaft - 3305-. Do not tilt the seal.
- Install the flange shaft.
- Tighten the new screw to 30 Nm. Push the flange shaft against the transmission so that the bolt engages in the thread.
- Attach the right drive axle to the flange shaft or install the right drive axle. Refer to ⇒ Suspension, Wheels, Steering; Rep. Gr. 40; Drive Axles, Removing and Installing.
- Refill any transmission fluid that may have leaked out while removing the seal. Refer to [⇒ 1 Transmission Fluid, Replacing](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/34-controls-housing/transmission-fluid-replacing/).

> **Note**
>
> The transmission fluid must be replaced to assure the transmission fluid level is correct.

- Install the noise insulation. Refer to ⇒ Body Exterior; Rep. Gr. 50; Noise Insulation.

## Tightening torques on this page

### In the steps
| Step | Torque |
| --- | --- |
| Tighten the new screw to 30 Nm. Push the flange shaft against the transmission so that the bolt engages in the thread. | 30 Nm |
