# 1.3 Left Stub Shaft Seal, Replacing – 7-speed DSG gearbox 0AM (DQ200)

> DSG 0AM left stub shaft oil seal, replacing (Seals) on the VW Polo 6R/6C: 13 steps, special tools VW771 and VW771/37, tightening torques and 4 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/39-final-drive-differential/left-stub-shaft-seal-replacing/
- Original document: https://cdn.polo.blue/files/7-speed_dual_clutch_transmission_0am-eng.pdf
- 39 – Final Drive, Differential, [7-speed DSG gearbox 0AM (DQ200)](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/index.md)
- Previous procedure: [1.2 Right Stub Shaft Seal, Replacing](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/39-final-drive-differential/right-stub-shaft-seal-replacing/index.md)
- Next procedure: [1.4 Right Flange Shaft Seal, Replacing](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/39-final-drive-differential/right-flange-shaft-seal-replacing/index.md)

Right side. Refer to [⇒ 1.2 Right Stub Shaft Seal, Replacing](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/39-final-drive-differential/right-stub-shaft-seal-replacing/#t210-508)

Special tools and workshop equipment required

- Slide Hammer Set - VW771-
- Slide Hammer Set - Hook - VW771/37-
- Seal Installer - Flange Shaft - 3305-
- Socket And Extended Bit - T10107A- or Long Hex Socket - VAG1669-
- Used Oil Collection and Extraction Unit - SMN372500-
- Sealing Grease - G 052 128 A1-

**Removing**

> **Note**
>
> - Do not remove both drive axles from the transmission at the same time. Then it would not be possible to hold the opposite front wheel in place in order to remove or install the stub shaft bolts.
> - Do not remove both stub shafts from the transmission at the same time. If the differential bevel gear turns in the differential then the bolts for the stub shafts are very difficult to reinstall.

- Remove the drive axle. Refer to ⇒ Suspension, Wheels, Steering; Rep. Gr. 40; Drive Axles, Removing and Installing.
- Place the Used Oil Collection and Extraction Unit - SMN372500- or Drip Tray under the transmission.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/23332d7b35b6ada8.webp)

- Remove the bolt in the stub shaft using the Socket And Extended Bit - T10107A- or Long Hex Socket - VAG1669-.
- Remove the stub shaft.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/881509dc342d7510.webp)

- Remove the stub shaft seal using the Slide Hammer Set - VW771- and Slide Hammer Set - Hook - VW771/37-.

The seal can also be removed using the Puller - Crankshaft/Power Steering Seal - T20143-.

**Installing**

- Lightly oil the new gasket on the outer circumference.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/c144c0d66fb49eaa.webp)

- Fill the space between the sealing and dust lip halfway with Sealing Grease - G 052 128- -arrow-.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/58cb37aee7280676.webp)

- Install the seal all the way in without tilting it.

If necessary, a new dust ring can be pressed on the stub shaft using Bearing Installer - Multiple Use - 40 - 20-. Do not use a hammer.

- Insert the stub shaft.
- Tighten the stub shaft bolt to 30 Nm. Push the stub shaft against the transmission so that the bolt engages in the thread.
- Reinstall the drive axle. Refer to ⇒ Suspension, Wheels, Steering; Rep. Gr. 40; Drive Axles, Removing and Installing.
- Refill any transmission fluid that may have leaked out while removing the seal. Refer to [⇒ 1 Transmission Fluid, Replacing](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/34-controls-housing/transmission-fluid-replacing/).

> **Note**
>
> The transmission fluid must be replaced to assure the transmission fluid level is correct.

- Install the noise insulation. Refer to ⇒ Body Exterior; Rep. Gr. 50; Noise Insulation.

## Tightening torques on this page

### In the steps
| Step | Torque |
| --- | --- |
| Tighten the stub shaft bolt to 30 Nm. Push the stub shaft against the transmission so that the bolt engages in the thread. | 30 Nm |
