# 1.5 Left Flange Shaft Seal, Replacing – 7-speed DSG gearbox 0AM (DQ200)

> DSG 0AM left flange shaft oil seal, replacing (Seals) on the VW Polo 6R/6C: 23 steps, special tools VW771 and 3305, tightening torques and 9 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/39-final-drive-differential/left-flange-shaft-seal-replacing/
- Original document: https://cdn.polo.blue/files/7-speed_dual_clutch_transmission_0am-eng.pdf
- 39 – Final Drive, Differential, [7-speed DSG gearbox 0AM (DQ200)](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/index.md)
- Previous procedure: [1.4 Right Flange Shaft Seal, Replacing](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/39-final-drive-differential/right-flange-shaft-seal-replacing/index.md)
- Next procedure: [2 Special Tools](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/39-final-drive-differential/special-tools/index.md)

Right side. Refer to [⇒ 1.4 Right Flange Shaft Seal, Replacing](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/39-final-drive-differential/right-flange-shaft-seal-replacing/#t214-349)

Special tools and workshop equipment required

- Slide Hammer Set - VW771-
- Seal Installer - Flange Shaft - 3305-
- Tensioning Strap - T10038-
- Socket And Extended Bit - T10107A- or Long Hex Socket - VAG1669-
- Used Oil Collection and Extraction Unit - SMN372500-
- Sealing Grease - G 052 128 A1-

**Removing**

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/8385b1b30e49f71c.webp)

> **Note**
>
> - Do not remove all the bolts in the left and right flange shafts at the same time. If the differential bevel gears rotate, it will be difficult to install the bolts.
> - The drive axle must be removed from the transmission and set to the side. The drive axle is secured with the Tensioning Strap - T10038- to the suspension strut.
> - The bolt for the drive axle to wheel bearing housing connection does not need to be loosened.

- Remove the noise insulation. Refer to ⇒ Body Exterior; Rep. Gr. 50; Noise Insulation.
- Remove the left wheel housing liner. Refer to ⇒ Body Exterior; Rep. Gr. 66; Wheel Housing Liner; Overview - Front Wheel Housing Liner.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/a8910b02f13124ff.webp)

- If equipped, remove the Left Front Level Control System Sensor - G78- from the control arm.

Tightening specification. Refer to ⇒ Suspension, Wheels, Steering; Rep. Gr. 40; Front Suspension and Control Arm; Overview

- Front Suspension and Control Arm.
- Turn the steering wheel all the way to the left and remove the left drive axle from the flange shaft. Refer to ⇒ Suspension, Wheels, Steering; Rep. Gr. 40; Drive Axles, Removing and Installing.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/2c787ace1d341e97.webp)

- Remove only the left control arm from the ball joint -arrows-.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/03225024746b4b19.webp)

- Remove the nut -1- from the coupling rod -3-. Refer to ⇒ Suspension, Wheels, Steering; Rep. Gr. 40; Front Suspension and Control Arm; Overview - Front Suspension and Control Arm or ⇒ Suspension, Wheels, Steering; Rep. Gr. 40; Front Suspension and Control Arm; Overview - Front Suspension and Control Arm.
- Remove the coupling rod and turn the stabilizer bar -2- slightly upward.
- Swivel the left drive axle into the wheel housing.
- Tie up the drive axle as high as possible. Do not damage the paint on the drive axle.
- Place the Used Oil Collection and Extraction Unit - SMN372500- or Drip Tray under the transmission.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/b34289ddb2dbcd45.webp)

- Remove the left flange shaft bolt at the transmission using the Socket And Extended Bit - T10107A-. Insert two bolts in the flange and counterhold with a tire iron.

The bolt has 6 mm inner hex. The bolt can also be removed and installed using the Long Hex Socket - VAG1669-.

- Remove the flange shaft.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/a90df5a3d86f21f0.webp)

- Remove flange shaft seal.

**Installing**

- Lightly oil the new gasket on the outer circumference.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/050f03f8f06fd380.webp)

- Fill the space with the new seal between the sealing and dust lip halfway with Sealing Grease - G 052 128- -arrow-.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/58cb37aee7280676.webp)

- Drive in the new seal all the way using the Seal Installer - Flange Shaft - 3305-. Do not tilt the seal.
- Install the flange shaft.
- Tighten the new bolt to 30 Nm. Push the flange shaft against the transmission so that the bolt engages in the thread.
- Reinstall the drive axle. Refer to ⇒ Suspension, Wheels, Steering; Rep. Gr. 40; Drive Axles, Removing and Installing.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/5e23db8fe0a7053b.webp)

- Reattach the control arm and coupling rod. Refer to ⇒ Suspension, Wheels, Steering; Rep. Gr. 40; Front Suspension and Control Arm; Overview - Front Suspension and Control Arm or ⇒ Suspension, Wheels, Steering; Rep. Gr. 40; Front Suspension and Control Arm; Overview - Front Suspension and Control Arm.
- Refill any transmission fluid that may have leaked out while removing the seal. Refer to [⇒ 1 Transmission Fluid, Replacing](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/34-controls-housing/transmission-fluid-replacing/).

> **Note**
>
> The transmission fluid must be replaced to assure the transmission fluid level is correct.

- Install the noise insulation. Refer to ⇒ Body Exterior; Rep. Gr. 50; Noise Insulation.
  огромный архив документации по автомобилям Volkswagen, Skoda, Seat, Audi 

## Tightening torques on this page

### In the steps
| Step | Torque |
| --- | --- |
| Tighten the new bolt to 30 Nm. Push the flange shaft against the transmission so that the bolt engages in the thread. | 30 Nm |
