# 2.1 Parking Lock Cover, Removing and Installing – 7-speed DSG gearbox 0AM (DQ200)

> VW Polo 6R/6C, step by step: DSG 0AM parking lock cover, removing and installing – 12 steps, tightening torques and 4 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/35-gears-shafts/parking-lock-cover-removing-and-installing/
- Original document: https://cdn.polo.blue/files/7-speed_dual_clutch_transmission_0am-eng.pdf
- 35 – Gears, Shafts, [7-speed DSG gearbox 0AM (DQ200)](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/index.md)
- Previous procedure: [1 Gears and Shafts, Disassembling and Assembling](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/35-gears-shafts/gears-and-shafts-disassembling-and-assembling/index.md)
- Next procedure: [2.2 Parking Lock, Removing and Installing](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/35-gears-shafts/parking-lock-removing-and-installing/index.md)

Special tools and workshop equipment required

- Pry Lever - 80-200-

**Removing**

- The transmission is installed.
- The selector lever is in »P«.

- Remove the air filter housing:

- Gasoline engine. Refer to ⇒ Rep. Gr. 24; Air Filter; Overview - Air Filter Housing.
- TDI engine. Refer to ⇒ Rep. Gr. 23; Diesel Direct Injection System; Overview - Air Filter.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/7e5664cb7f4e30f6.webp)

- Remove the battery and the battery tray -arrows-. Refer to ⇒ Electrical Equipment; Rep. Gr. 27; Battery; Battery, Removing and Installing.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/60c8a16a09e6d623.webp)

- Remove the lock washer -1- from the selector lever cable.

Always replace the circlip on the selector lever cable.

- Remove the selector lever cable -2- from the ball head on the selector lever using, for example, a Pry Lever - 80-200-.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/9c3f78eadcaf5aa1.webp)

> **Note**
>
> - Use pliers to remove the lock washer -1-. Do not use a sharpedged lever. Otherwise the selector lever cable could get damaged.
> - Remove the cable bracket -A- and selector lever cable from the transmission, if necessary. To do this, remove the bolts -arrows-. These bolts must be replaced.
> - Bolt tightening specification -arrows-: 8 Nm +90° additional turn.

> **Caution**
>
> Risk of damaging the selector lever cable.
>
> - Do not push the selector lever cable out of the cable bracket toward the rear. When removing the parking lock cover, first guide the selector lever cable out of the cable bracket.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/12b9f3cca4523d9d.webp)

- Remove the bolt -3- and remove the selector lever -4-.
- Remove the bolts -2- and the parking lock cover -1-.

**Installing**

The parking lock cover must be replaced if there are leaks on the gearshift shaft seal or on the parking lock cover.

- Clean the sealing surface and the parking lock cover -1-.
- Install the parking lock cover -1- and the bolts -2-.
- Install the selector lever -4- and the bolt -3-.
- Adjust the selector lever cable. Refer to.

Further installation is performed in the reverse order of the removal.

- Install the battery and the battery tray. Refer to ⇒ Electrical Equipment; Rep. Gr. 27; Battery; Battery, Removing and Installing.
- Install the air filter housing:

- Gasoline engine. Refer to ⇒ Rep. Gr. 24; Air Filter; Overview - Air Filter Housing.
- TDI engine. Refer to ⇒ Rep. Gr. 23; Diesel Direct Injection System; Overview - Air Filter.

**Tightening Specifications**

| Component | Tightening Specification |
| --- | --- |
| Parking lock cover to transmission housing | 8 Nm |
| Transmission selector lever to selector shaft. | 15 Nm |

огромный архив документации по автомобилям Volkswagen, Skoda, Seat, Audi 

## Tightening torques on this page

### In the steps
| Step | Torque |
| --- | --- |
| Bolt tightening specification -arrows-: 8 Nm +90° additional turn. | 8 Nm +90° |

### Torque
| Part | Torque |
| --- | --- |
| Parking lock cover to transmission housing | 8 Nm |
| Transmission selector lever to selector shaft. | 15 Nm |
