# 6 Transmission, Transporting and Securing To Assembly Stand – 7-speed DSG gearbox 0AM (DQ200)

> VW Polo 6R/6C, step by step: transporting DSG 0AM and securing it to an assembly stand – 3 steps, special tools VW309A, VW353 and 2024A and 4 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/34-controls-housing/transmission-transporting-securing-assembly-stand/
- Original document: https://cdn.polo.blue/files/7-speed_dual_clutch_transmission_0am-eng.pdf
- 34 – Controls, Housing, [7-speed DSG gearbox 0AM (DQ200)](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/index.md)
- Previous procedure: [3.6 Overview – Shift Forks with Mechatronic Removed](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/34-controls-housing/overview-shift-forks-with-mechatronic-removed/index.md)
- Next procedure: [7 Special Tools](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/34-controls-housing/special-tools/index.md)

Special tools and workshop equipment required

- Holding Plate - VW309A-
- Transmission Support - VW353-
- Engine Sling - 2024A-
- Lifting Eyebolt - 3368-
- Engine and Gearbox Bracket - VAS6095A-
- Shop Crane - VAS6100-
- Engine/Gearbox Support Shackle (2 pc.) - 10-222A/12-
- Engine Bung Set - VAS6122-
- Protective Cap - 02M 409 120-, alternative for Engine Bung Set - VAS6122-
- Protective Cap - 0AM 325 120 A-

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/3fa9beee761824b0.webp)

**Transmission, Transporting**

> **Note**
>
> Seal the transmission oil-tight, if necessary. Refer to [⇒ 6 Transmission, Transporting and Securing To Assembly Stand](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/34-controls-housing/transmission-transporting-securing-assembly-stand/#t196-82).

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/99664dea440bd47e.webp)

Seal the Transmission So That No Fluid Can Leak Out.

> **Caution**
>
> Risk of damaging the transmission.

The vent on the DSG Transmission Mechatronic - J743- (-rear arrow-) and the transmission ventilation (-left front arrow-) must be sealed tight so that no fluid can leak out during assembly work.

- Fluid that has leaked out of the DSG Transmission Mechatronic - J743- hydraulic area may not be refilled or checked. Checking the hydraulic fluid level in the DSG Transmission Mechatronic - J743- is not possible.
- If transmission fluid has leaked out, then it is necessary to perform a transmission fluid replacement. It is not possible to check the fluid level.
- Underfilling or overfilling both fluid systems will impair the function of the transmission.

- Remove both vent caps -arrows- and seal with clean oil-tight plugs from the Engine Bung Set - VAS6122-.

> **Note**
>
> - On some transmissions, the breather cap on the Mechatronic is destroyed during removal and must be replaced.
> - As an alternative to the Engine Bung Set - VAS6122-, the Protective Cap - 02M 409 120- can be used to seal the transmission. It is also possible to securely seal the Mechatronic using the Cap - 0AM 325 120 A-. Refer to Parts Catalog.

- Seal the transmission ventilation and DSG Transmission Mechatronic - J743- vent using clean plugs from the Engine Bung Set - VAS6122-.
- If necessary, order a new vent cap arrow for the DSG Transmission Mechatronic - J743-. It must be replaced after installing the transmission. Refer to the Parts Catalog.

- The seals must be removed after installing the transmission and the vent caps must be reinstalled or replaced.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/e457d7fd9ab75ffa.webp)

Secure the Transmission on the Transmission Support - VW353-.

Requirement:

- The transmission is sealed so that no fluid can leak out. Refer to [⇒ 6 Transmission, Transporting and Securing To Assembly Stand](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/34-controls-housing/transmission-transporting-securing-assembly-stand/#t196-82).

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/10ef90ca9341d5a4.webp)

Lift the Transmission into the Assembly Stand.

Requirement:

- The transmission is sealed so that no fluid can leak out. Refer to [⇒ 6 Transmission, Transporting and Securing To Assembly Stand](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/34-controls-housing/transmission-transporting-securing-assembly-stand/#t196-82).

The transmission is lifted together with the Transmission Support - VW353- »into the assembly stand«.
