# 1 Transmission Fluid, Replacing – 7-speed DSG gearbox 0AM (DQ200)

> VW Polo 6R/6C, step by step: replacing DSG 0AM gearbox oil (transmission fluid) – 18 steps, special tools SMN372500 and VAS6262A and 10 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/34-controls-housing/transmission-fluid-replacing/
- Original document: https://cdn.polo.blue/files/7-speed_dual_clutch_transmission_0am-eng.pdf
- 34 – Controls, Housing, [7-speed DSG gearbox 0AM (DQ200)](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/index.md)
- Previous procedure: [4 Special Tools](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/special-tools/index.md)
- Next procedure: [3.1 DSG Transmission Mechatronic J743 Safety Precautions](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/34-controls-housing/mechatronic-j743-safety-precautions/index.md)

Special tools and workshop equipment required

- Used Oil Collection and Extraction Unit - SMN372500-
- Oil Filler - VAS6262A- with Adapter For Oil Filling - VAS6262/4-

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/8e553d017fcf213f.webp)

- It is necessary to use the Oil Filler - Adapter 6 - VAS6262/6- on some oil containers.
- It may be necessary to shorten the bleed pipe on the Adapter For Oil Filling - VAS6262A-. Refer to [⇒ 1 Transmission Fluid, Replacing](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/34-controls-housing/transmission-fluid-replacing/#t74-503).
- Container with the transmission fluid for the 7-speed DSG® transmission 0AM. Refer to the Parts Catalog for the part number. 

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/e459c165f723bf65.webp)

Measuring the Length of the Bleed Pipe on the Adapter For Oil Filling - VAS6262A- and Shortening if Necessary.

The bleed pipe on the Adapter For Oil Filling - VAS6262A- must be shorted to dimension -a- so that it does not touch the bottom on some containers.

- Dimension -a- = 210 mm

> **Note**
>
> Dimension -a- is measured starting from the shaft (the green surface in the magnified area) on the adapter for the Oil Filler - VAS6262A-.

If dimension -a- is greater than 210 mm: 

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/7fb0ea9b2713e0c8.webp)

- Make a mark on the bleed pipe, dimension -a-, and cut it, with for example the Brake Line Tool Kit - Pipe Cutter - VAS6056/2-.
- Clean the Oil Filler - VAS6262A-.

**Procedure**

> **Note**
>
> - The transmission fluid is a permanent filling. For this reason, a fluid level check is not necessary on this transmission.
> - A fluid level check does therefore not exist.
> - If leaks occur at the transmission, the cause is to be determined and faults must be corrected.
> - After that it is necessary to drain all the transmission fluid and fill it again.

- Raise the vehicle.
- Remove the noise insulation. Refer to ⇒ Body Exterior; Rep. Gr. 50; Noise Insulation.
- Place the Used Oil Collection and Extraction Unit - SMN372500- or Drip Tray under the transmission.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/6410aee64471299b.webp)

- Remove the drain plug from the transmission.
- Drain the fluid and then install the drain plug and tighten it.

> **Note**
>
> - It is not possible to check the transmission fluid level.
> - Fill the fluid exactly to the specified quantity.
> - This assures the transmission is filled correctly.
> - Underfilling or overfilling the transmission fluid will cause the transmission to malfunction.

> **Caution**
>
> Risk of damaging the transmission.
>
> - Use only the transmission fluid specifically for the 7-speed DSG® transmission 0AM. It is available as a replacement part. Refer to the Parts Catalog.
> - Using other fluids can cause malfunctions or transmission failure.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/7e5664cb7f4e30f6.webp)

- Remove the battery and the battery tray -arrows-. Refer to ⇒ Electrical Equipment; Rep. Gr. 27; Battery; Battery, Removing and Installing.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/e843e95702ba1b12.webp)

- Remove the bleed cap -arrow- next to the transmission gearshift lever.

> **Note**
>
> For clarity, the installation position is pictured with the transmission removed.

> **Caution**
>
> Risk of damaging the transmission.
>
> - The Oil Filler - VAS6262A- with the Adapter For Oil Filling
>   - VAS6262/4- must be clean and transmission fluid must not be mixed with another fluid!

- Shake the container before opening.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/b0cb4c517acab015.webp)

- Attach the transmission fluid container for the 7-speed DSG® transmission 0AM to the Adapter For Oil Filling - VAS6262A-. Refer to the Parts Catalog for the part number.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/ca1358c33c2a9510.webp)

> **Note**
>
> Use the Oil Filler - Adapter 6 - VAS6262/6- if the container thread does not fit on the Adapter For Oil Filling - VAS6262A-.

- Hold the container so that no fluid can run into the filling hose.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/6c562a15448c9858.webp)

- Connect the Oil Filler - Adapter 4 - VAS6262/4- to the filling hose and mount it on the bleeder on the transmission.
- Screw in the container and fill 1.7 liters (1.79 quarts) of transmission fluid.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/81acb41735aa93d6.webp)

- Remove the Oil Filler - VAS6262A- after filling. Wipe the area around the bleed hole with a clean cloth and install the bleeder cap -arrow-.
- Install the battery tray and the battery -arrows-. Refer to ⇒ Electrical Equipment; Rep. Gr. 27; Battery; Battery, Removing and Installing.
- Install the noise insulation. Refer to ⇒ Body Exterior; Rep. Gr. 50; Noise Insulation.
