# 3.2 Overview – Mechatronic – 7-speed DSG gearbox 0AM (DQ200)

> Mechatronic J743 overview, DSG gearbox 0AM (DSG Transmission Mechatronic J743) on the VW Polo 6R/6C: tightening torques and 2 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/34-controls-housing/overview-mechatronic/
- Original document: https://cdn.polo.blue/files/7-speed_dual_clutch_transmission_0am-eng.pdf
- 34 – Controls, Housing, [7-speed DSG gearbox 0AM (DQ200)](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/index.md)
- Previous procedure: [3.1 DSG Transmission Mechatronic J743 Safety Precautions](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/34-controls-housing/mechatronic-j743-safety-precautions/index.md)
- Next procedure: [3.3 DSG Transmission Mechatronic J743, Removing with Transmission Installed](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/34-controls-housing/mechatronic-j743-removing-gearbox-installed/index.md)

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/bb6cf4572b301663.webp)

- **1** Bolt
  - 10 Nm
  - M8 x 35
  - Always replace after removing

> **Note**
>
> - Do not remove bolts without consideration.
> - Always read the removal descriptions.

- **2** Bolt
  - 10 Nm
  - M8 x 90
  - Always replace after removing
- **3** DSG Transmission Mechatronic - J743-

> **Note**
>
> - Note the following when installing a new Mechatronic:
> - Do not dispose of the packaging and the closure cap for the vent pipe of a new Mechatronic after unpacking it. They are required for returning the removed Mechatronic.
> - The fluid in a »new« Mechatronic is already filled correctly. Do not drain or add any fluid.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/16f15d02b2941a65.webp)

Pay attention to the vent when handling the Mechatronic.

- When doing assembly work on the Mechatronic, please remove the cap -arrow- from the vent and seal the vent with a suitable plug.

The Protective Cap - 0AM 325 120- is well suited for this.

> **Caution**
>
> On some transmissions, the breather cap on the Mechatronic is destroyed during removal and must be replaced.

Checking the hydraulic fluid level for the Mechatronic is not possible. The Mechatronic vent must be sealed oil-tight before performing any assembly work.

Fluid that has leaked out of the Mechatronic hydraulic area may not be refilled or checked. Replace the Mechatronic if fluid is leaking.

## Tightening torques on this page

### Torque [To the drawing](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/34-controls-housing/overview-mechatronic/#t108-292)
**All items:** Always replace after removing

| Item | Part | Torque | Notes |
| --- | --- | --- | --- |
| 1 | Bolt | 10 Nm | M8 x 35 |
| 2 | Bolt | 10 Nm | M8 x 90 |
