# 3.4 DSG Transmission Mechatronic J743, Moving into »Removal Position« by Hand – 7-speed DSG gearbox 0AM (DQ200)

> VW Polo 6R/6C, step by step: moving mechatronic J743 into removal position by hand – 14 steps, tightening torques and 10 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/34-controls-housing/mechatronic-j743-moving-into-removal-position/
- Original document: https://cdn.polo.blue/files/7-speed_dual_clutch_transmission_0am-eng.pdf
- 34 – Controls, Housing, [7-speed DSG gearbox 0AM (DQ200)](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/index.md)
- Previous procedure: [3.3 DSG Transmission Mechatronic J743, Removing with Transmission Installed](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/34-controls-housing/mechatronic-j743-removing-gearbox-installed/index.md)
- Next procedure: [3.5 DSG Transmission Mechatronic J743, Installing](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/34-controls-housing/mechatronic-j743-installing/index.md)

Special tools and workshop equipment required

- Pry Lever - 80-200- 

Sometimes it may not be possible to remove the Mechatronic. In this case, the gear selector will get »caught« at the »top left side« on the transmission housing -arrow-.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/b254f6748d8a8368.webp)

The gear selector that is »caught« -arrow- can be pushed into a »removal position« by hand. Slide a shift fork behind the parking lock cover to do this. Do this according to the following procedure:

- Place the Mechatronic back on the transmission housing and secure the Mechatronic with a screw.
- Move the selector lever into “P”.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/81d363f411bfabb1.webp)

- Remove the lock washer in the direction of the -arrow-.

Always replace the circlip on the selector lever cable.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/e2eb951a0de0d118.webp)

> **Note**
>
> - Use pliers to remove the lock washer. Do not use a sharpedged lever. Otherwise the selector lever cable could get damaged.
> - Remove the cable bracket -A- and selector lever cable from the transmission, if necessary. To do this, remove the bolts -arrows-. These bolts must be replaced.
> - Bolt tightening specification -arrows-: 8 Nm +90° additional turn.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/234c42bd62e20e15.webp)

- Remove the selector lever cable from the ball head on the selector lever using, for example, a Pry Lever - 80-200-.
- Push the selector lever all the way toward the cable bracket by hand.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/4b5acecde36b5455.webp)

- Remove the selector lever.
- Remove the cover.

> **Caution**
>
> The Mechatronic does not »get caught« after the next step. This means it will fall out under certain circumstances. Secure the Mechatronic to the transmission with a bolt to prevent it from falling down.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/2ae0a8d5d217c290.webp)

- Push the shift fork to the side through the opening in direction of -arrow-.

(Press in the direction of travel to the left).

The gear selector that is »caught« will also be pushed back and it will be possible to remove the Mechatronic.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/f838955338a9b083.webp)

- After completing the work on the Mechatronic and it is installed, fill the transmission fluid via the parking lock.

> **Note**
>
> - When filling the transmission with transmission fluid via the parking lock, it is not necessary to remove the transmission bleed cap on the parking lock cover. It is possible to fill the transmission fluid directly on the parking lock.
> - Procedure, capacities and transmission fluid specification. Refer to [⇒ 1 Transmission Fluid, Replacing](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/34-controls-housing/transmission-fluid-replacing/).

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/15013b6c31796be9.webp)

- Lubricate the seal in the parking lock cover with Sealing Grease - G 052 128 A1-.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/e38c94cddbb6cd17.webp)

- Attach the cover and gearshift lever again.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/e2c89d23cf00d9e4.webp)

- Press the selector lever cable onto the ball head on the selector lever again and install the new lock washer.
- Always replace the circlip on the selector lever cable.
- Adjust the selector lever cable. Refer to.

## Tightening torques on this page

### In the steps
| Step | Torque |
| --- | --- |
| Bolt tightening specification -arrows-: 8 Nm +90° additional turn. | 8 Nm +90° |
