# 3.5 DSG Transmission Mechatronic J743, Installing – 7-speed DSG gearbox 0AM (DQ200)

> Installing mechatronic J743, DSG gearbox 0AM on the VW Polo 6R/6C: 31 steps, special tool T10406, tightening torques and 14 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/34-controls-housing/mechatronic-j743-installing/
- Original document: https://cdn.polo.blue/files/7-speed_dual_clutch_transmission_0am-eng.pdf
- 34 – Controls, Housing, [7-speed DSG gearbox 0AM (DQ200)](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/index.md)
- Previous procedure: [3.4 DSG Transmission Mechatronic J743, Moving into »Removal Position« by Hand](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/34-controls-housing/mechatronic-j743-moving-into-removal-position/index.md)
- Next procedure: [3.6 Overview – Shift Forks with Mechatronic Removed](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/34-controls-housing/overview-shift-forks-with-mechatronic-removed/index.md)

Special tools and workshop equipment required

- Guide Bolt - Mechatronic - T10406-

> **Note**
>
> - The fluid in a »new« Mechatronic is already filled correctly.
> - The new Mechatronic is already sealed with the Protective Cap - 0AM 325 120 A-.
> - Do not dispose of the packaging and the closure cap for the vent pipe of a new Mechatronic after unpacking it. They are required for returning the removed Mechatronic.

**Installing**

> **Note**
>
> It must be certain that all shift forks are in -N- »in the center« and that the transmission is engaged in the neutral position.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/46d8e44e2d15f253.webp)

- Check each of the 4 shift forks by hand.

Each Shift Fork has 3 Settings: »gear engaged - neutral - gear engaged«.

- Shift each fork into every setting consecutively. Then remove all gears and set the shift forks back into »center position«.

> **Note**
>
> »Center position, neutral, neutral position«, otherwise the transmission will not work.

The front wheel can be turned slightly for support. Then the forks will shift »easier«.

- Clean the sealing surface that the Mechatronic will later rest on.

Oil residue on the sealing surface causes the future error diagnosis to be »leaking«.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/5c057bb48455471b.webp)

- Install the Guide Bolt - Mechatronic - T10406- hand-tight.

Make sure all 4 gear positioners stick out 25 mm -a-.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/216bd8f312abf741.webp)

> **Caution**
>
> Use caution when handling. Pry the plunger out of the Mechatronic and make sure it is not being supported on the sensors.

- Please clean the Mechatronic sealing surface.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/c2babde85b831cda.webp)

- Check the seal on the Mechatronic.

The seal must be fastened all around.

- Pay attention to the Transmission Input Speed Sensor 3 - G641-. The clip must not be damaged.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/1afdec94171df2b8.webp)

The Assembly Lever - T10407- is inserted between the engaging lever and the transmission housing.

The two alignment sleeves -1 and 2- for centering the Mechatronic on the transmission housing must be installed.

- Mount the Mechatronic.
- When handling and mounting, make sure the shift forks are not accidentally pushed out of their position.
- Also pay attention to the engaging lever and plunger at the Mechatronic.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/5bbb493c121ff02e.webp)

- Install 7 new bolts hand-tight.
- Remove the Guide Bolt - Mechatronic - T10406- again.
  огромный архив документации по автомобилям Volkswagen, Skoda, Seat, Audi 

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/1b699cfbd439a48c.webp)

- Make sure the plungers fit correctly in the engaging lever socket when doing so.
- Pull the plungers out far enough until they fit correctly in the sockets.

The plungers can be brought into position using a bent welding wire hook (self-made).

- Now check the plunger positions once again.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/397fb0f346798509.webp)

Plungers that are positioned incorrectly will damage the Mechatronic.

- Diagonally tighten the Mechatronic to 10 Nm.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/8566d369029fa6d2.webp)

- Turn the Assembly Lever - Mechatronic - T10407- to the right and remove.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/394d937bc81b2045.webp)

- Install the Transmission Input Speed Sensor 3 - G641-.
- Watch the sensor. The clip must not be damaged.

- The sensor must fit completely in its retainer and must be touching the transmission housing. Replace the Mechatronic if the sensor is »loose« or if the clip is broken.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/16f15d02b2941a65.webp)

- Remove the plug and mount the vent cap -arrow-.

> **Caution**
>
> Danger of causing damage to transmission components.
>
> - Never touch the contacts in the transmission connector. The control module as well as the Mechatronic can become damaged by the static discharge.

- To discharge any static electricity, touch vehicle ground with hand (without wearing a glove). Refer to [⇒ 7.2 Transmission](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/00-general-technical-data/transmission/#t16-538).
- Connect and lock the Mechatronic connector.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/e1620f4dd795e40e.webp)

- Attach all of the front brackets to the transmission.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/0179e95695c84276.webp)

Some Vehicles have A Cover Over the Engaging Levers.

The cover prevents dirt from getting in.

Tightening Specification: 8 Nm.

Now fill the transmission fluid. Refer to [⇒ 1 Transmission Fluid, Replacing](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/34-controls-housing/transmission-fluid-replacing/).

- Install the starter. Refer to ⇒ Electrical Equipment; Rep. Gr. 27; Starter; Starter, Removing and Installing.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/fa1b43a1077b728a.webp)

- If removed, install the charge air or coolant hoses.
- Install the battery and the battery tray. Refer to ⇒ Electrical Equipment; Rep. Gr. 27; Battery; Battery, Removing and Installing.
- Install the air filter housing:

- Gasoline engine. Refer to ⇒ Rep. Gr. 24; Air Filter; Overview - Air Filter Housing.
- TDI engine. Refer to ⇒ Rep. Gr. 23; Diesel Direct Injection System; Overview - Air Filter.

- Fill the coolant if necessary. Refer to ⇒ Rep. Gr. 19; Cooling System Components.
- Install the noise insulation. Refer to ⇒ Body Exterior; Rep. Gr. 50; Noise Insulation.
- Connect the Vehicle Diagnostic Tester and Perform basic
  measurement. Refer to
  [⇒ 7.3.3 Basic Measurement, Performing](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/00-general-technical-data/working-with-vehicle-diagnostic-testers/#7-3-3-basic-measurement-performing).
- If necessary, place the plug on the »removed« Mechatronic.

Now the Mechatronic can be sealed for shipping.

## Tightening torques on this page

### In the steps
| Step | Torque |
| --- | --- |
| Diagonally tighten the Mechatronic to 10 Nm. | 10 Nm |
| Tightening Specification: 8 Nm. | 8 Nm |
