# 2.3 “K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011 – 7-speed DSG gearbox 0AM (DQ200)

> VW Polo 6R/6C, step by step: adjusting K1 and K2 engaging bearings, DSG 0AM from 06/2011 – 39 steps, special tool VAS6594 and tightening torques.

- Web page: https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/k1-k2-engaging-bearing-position-adjusting-from-06-2011/
- Original document: https://cdn.polo.blue/files/7-speed_dual_clutch_transmission_0am-eng.pdf
- 30 – Clutch, [7-speed DSG gearbox 0AM (DQ200)](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/index.md)
- Previous procedure: [2.2 Dual Clutch, Removing, Transmission Production Date from 06/2011](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/dual-clutch-removing-from-06-2011/index.md)
- Next procedure: [2.4 Dual Clutch, Installing, Transmission Production Date from 06/2011](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/dual-clutch-installing-from-06-2011/index.md)

> **Caution**
>
> The following components must also be replaced if the dual clutch is replaced:
>
> - Both engaging levers with engaging bearing.
> - Ball stud for the “K 2” engaging lever.
> - Engaging bearing shims.

When replacing the dual clutch and its components, the “K 1 and K 2” engaging bearing position must always be readjusted.

> **Note**
>
> - It is not necessary to perform an adjustment if all the components mentioned are only removed and reinstalled.
> - The locking ring must be replaced in each case.

**Brief Description**

- The position of the engaging bearing is comparable to clutch play on a manual transmission. There are tolerances in the 7-speed DSG® transmission 0AM engaging system and in the transmission itself. There are also tolerances within the dual clutch. These tolerances must be taken into account separately when performing the adjustments.
- The following procedure describes how all necessary measurements are determined from the transmission side in order to select the correct shim. In addition to this, the tolerances in the clutch already determined by the manufacturer. The transmission side tolerances and the tolerances in the clutch determine the thickness of the shim.
- Follow the work sequence.

**Overview - Clutch Mechanism**

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/70686cd001be6764.webp)

- **1** Shim for “K 1”
  - Refer to [⇒ 2.3 K 1 and K 2 Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/k1-k2-engaging-bearing-position-adjusting-from-06-2011/#t49-531)
- **2** Large Engaging Lever for “K 1”
  - With engaging bearing
  - Always replace when replacing the dual clutch
- **3** Engaging Lever Support
  - For the large engaging lever “K 1”
  - Is not replaced
- **4** Small Engaging Bearing for “K 2”
  - Always replace when replacing the dual clutch
- **5** Shim for “K 2”
  - Refer to [⇒ 2.3 K 1 and K 2 Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/k1-k2-engaging-bearing-position-adjusting-from-06-2011/#t49-531)
- **6** Guide Sleeve Upper Section
  - For the small engaging lever “K 2” 
  - Removed and installed together with the guide sleeve lower section
- **7** Small Engaging Lever for “K 2”
  - Is removed and installed together with the guide sleeve upper section and lower section
  - Always replace when replacing the dual clutch
- **8** Ball Stud
  - For the small engaging lever “K 2”
  - Always replace when replacing the dual clutch
- **9** Bolts 
  - 8 Nm +90°
  - Always replace after removing
- **10** Guide Sleeve Lower Section
  - For the small engaging lever “K 2”
  - Removed and installed together with the guide sleeve upper section

Special tools and workshop equipment required

- Digital Depth Gauge - 300mm - VAS6594-
- Gauge - Clutch Bearings - T10466-
- Ruler (2 pc.) - T40100-

**Requirement**

- The transmission flange must be even so that it has a good surface for the ruler.
- DSG Transmission Mechatronic - J743- must be installed.

> **Caution**
>
> Danger of damaging the clutch and other components.
>
> - The mount for the engaging lever and the entire mechanical system for the engaging bearing must be dry and free from oil and grease.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/848fd7b6aa37a6aa.webp)

- Remove the ball stud installed using pliers.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/059dd177e906da6d.webp)

- Install the »new« ball stud by hand. Use a plastic hammer and drift gently, if necessary.

> **Note**
>
> Tap the drift gently with a hammer to avoid damaging the ball stud.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/e8d78d7c38c89b48.webp)

- Install the old circlip for the outer input shaft.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/d71b8fbca6a24963.webp)

Step 1: Determine Dimension “B” for “K 1” and “K 2” Clutch.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/02838d21c6bc0aa1.webp)

- Place Ruler (2 pc.) - T40100- across the end of the shaft on the transmission flange.

> **Caution**
>
> There is the risk of incorrect measurements.
>
> - The Ruler (2 pc.) - T40100- should stay in this position for the following measurements. Do not move it or take if off.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/affcc92d8f72e9d4.webp)

- Place the Digital Depth Gauge - 300mm - VAS6594- on top of the Ruler (2 pc.) - T40100- and position the depth slide on the outer input shaft.
- Set the depth gauge to “0”.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/59795eaad1b2b891.webp)

- Position the depth slide on the locking ring, as illustrated.
- Measure dimension “B1 ” on the locking ring in this position.

- Example: measurement “B1 ” = 2.62 mm

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/eb0732eba0702a47.webp)

- Measure dimension “B2 ” on the opposite side of the locking ring.

> **Note**
>
> Do not measure on the end of the locking ring. The circlip could get pushed away and this would falsify the measurement.
>
> - Example: dimension “B2 ” = 2.58 mm

- Calculate the mean value from “B1 ” and “B2 ”.
  Formula: (B1 + B2) / 2

Example:

- (2.62 + 2.58) / 2 = 2.60 mm
- Result: dimension “B” = 2.60 mm

> **Note**
>
> If the dual clutch continues to be installed according to this measurement, then it must be removed now. Refer to [⇒ 2.2 Dual Clutch, Removing, Transmission Production Date from 06/2011](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/dual-clutch-removing-from-06-2011/#t47-608).

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/2292a15105d49e19.webp)

- Remove the circlip from the outer input shaft and dispose of it.

> **Warning**
>
> Do not re-use the locking ring. 

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/f288924856c25446.webp)

Step 2: Determine Dimension “A 1” for the “K 1” Clutch Engaging Bearing.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/b90eaedf39017a6d.webp)

- Install the large engaging lever.

> **Warning**
>
> Do not install the shim.

- Make sure the engaging lever fits correctly.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/fa1da28d9b93ae94.webp)

- Place the Gauge - Clutch Bearings - T10466- on the large engaging bearing. The flat side faces up
- Press and turn the Gauge - Clutch Bearings - T10466- to make sure it seats correctly on the engaging bearing.

- The engaging bearing turns with the Gauge - Clutch Bearings - T10466-.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/e380a77876dfb44c.webp)

- Place the Digital Depth Gauge - 300mm - VAS6594- on top of the ruler and position the depth slide on the outer input shaft.

- The Ruler (2 pc.) - T40100- lies straight across the transmission flange over the end of the shaft.

> **Caution**
>
> There is the risk of incorrect measurements.
>
> - The Ruler (2 pc.) - T40100- should stay in this position for the following measurements. Do not move it or take if off.

- Set the depth gauge to “0”.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/d13eab184ebdee27.webp)

- Position the depth slide on the Gauge - Clutch Bearings - T10466-, as illustrated.
- Measure dimension “A 1a ” on the Gauge - Clutch Bearings - T10466-.

- Example: dimension “A 1a ” = 4.93 mm

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/f2564197c47c5539.webp)

- Measure dimension “A 1b ” on the other side of the Gauge - Clutch Bearings - T10466-.

- Example: dimension “A 1b ” = 4.91 mm

- Calculate the average value from dimension “A 1a ” and “A 1b ”.
  Formula: (A 1a + A 1b) / 2

Example:

- (4.93 + 4.91) / 2 = 4.92 mm
- Result: dimension “A 1” = 4.92mm

Step 3: Determine the Height Tolerance for the “K 1” Clutch Engaging Bearing.

> **Note**
>
> Using dimension “A 1” and dimension “B”, calculate the height tolerance for clutch “K 1” engaging bearing as follows:

|  | Dimension “A 1” |
| --- | --- |
| – | Dimension “B” |
| = | Height tolerance for clutch “K 1” engaging bearing |

Example:

- 4.92 mm – 2.60 mm = 2.32 mm
- Result: height tolerance for “K 1” clutch engaging bearing = 2.32 mm 

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/08cd9c146ae840cf.webp)

Step 4: Determine the Clutch Tolerance for the “K 1” Clutch.

- Read the clutch tolerance value on the new clutch.

- Example: clutch tolerance read on the clutch “K 1 = +0.2”, as illustrated.
- Result: clutch “K 1” clutch tolerance = + 0.20 mm.

Step 5: Determine the “SK 1” Shim Thickness.

> **Note**
>
> Using the clutch tolerance of clutch “K 1”, now the thickness of shim “SK 1” can be calculated as follows:

|  | Height tolerance for the engaging bearing “K 1” |
| --- | --- |
| –/+ | Clutch tolerance for clutch “K 1” |
| = | Calculated thickness for shim “SK 1” |

Example:

- 2.32 mm + 0.20 mm = 2.52 mm
- Result: calculated “SK 1” shim thickness= 2.52 mm

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/d087769286cc5a88.webp)

- Select the shim from the table using the part number -magnifying glass- on the shim and lay it nearby for installation.

| Calculated Shim Thickness mm | Available Shim Thicknesses in mm | Shim Part Number |
| --- | --- | --- |
| 1.21 to 1.60 | 1.50 | 0AM 141 383 |
| 1.61 to 1.80 | 1.70 | 0AM 141 383 A |
| 1.81 to 2.00 | 1.90 | 0AM 141 383 B |
| 2.01 to 2.20 | 2.10 | 0AM 141 383 C |
| 2.21 to 2.40 | 2.30 | 0AM 141 383 D |
| 2.41 to 2.60 | 2.50 | 0AM 141 383 E |
| 2.61 to 2.80 | 2.70 | 0AM 141 383 F |
| 2.81 to 3.00 | 2.90 | 0AM 141 383 G |
| 3.01 to 3.20 | 3.10 | 0AM 141 383 H |
| 3.21 to 3.40 | 3.30 | 0AM 141 383 J |
| 3.41 to 3.80 | 3.50 | 0AM 141 383 K |

Example:

- Result: calculated “SK 1” shim thickness= 2.52 mm
- Selected shim thickness = 2.50 mm = part number 0AM 141 383 E

> **Caution**
>
> Only install these shims later to avoid damaging the clutch.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/b90eaedf39017a6d.webp)

- Remove the Gauge - Clutch Bearings - T10466- and large engaging lever.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/1b719d8da9a225d5.webp)

Step 6: Determine Dimension “A 2” for “K 2” Clutch Engaging Bearing

> **Note**
>
> The guide sleeve upper section cannot be removed or installed separately. It is always removed and installed together with the guide sleeve lower section and the »small« engaging lever.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/2267caf8547b9cf2.webp)

Note the Following when Installing A New »K2« Engaging Lever:

A new »K 2« engaging lever with guide sleeve upper and lower sections are in their shipment positions when they are delivered -image-, and they must first be moved into their installation position before installing.

Move the »K 2« engaging lever into its installation position: 

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/268ddbf935c8273c.webp)

- Hold the guide sleeve upper section with one hand. Turn the guide sleeve lower section in direction of -arrow- with the other hand until the sleeve moves freely.

> **Note**
>
> Hold both parts securely because a lot of force is needed to turn the guide sleeve lower section.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/9e1b51d59ff279bd.webp)

In the installed position, the holes in the guide sleeve lower section are at a right angle to the engaging lever and the sleeve can be moved freely.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/5dbe5d976711613f.webp)

**Continuation for All**

- Install the »small« engaging lever with the upper and lower sections of the guide sleeve. Insert new bolts and tighten them.

Tightening specification. Refer to [⇒ 2.3 “K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/k1-k2-engaging-bearing-position-adjusting-from-06-2011/#t51-206).

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/1a53ea0b5cfb04ae.webp)

- Install the »small« engaging bearing without the shim.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/7c5b4f4ac14f8916.webp)

> **Warning**
>
> Do not install the shim.
>
> - The small engaging bearing fits in only one position due to the 8 grooves.

- Turn the small engaging bearing to make sure it is installed correctly and fits correctly in the grooves.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/fa1da28d9b93ae94.webp)

- Place the Gauge - Clutch Bearings - T10466- on the small engaging bearing. The flat side faces up
- Press and turn the Gauge - Clutch Bearings - T10466- to make sure it seats correctly on the engaging bearing.

- The engaging bearing turns with the Gauge - Clutch Bearings - T10466-.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/79334bb5cb94f79e.webp)

- Place the Digital Depth Gauge - 300mm - VAS6594- on top of the ruler and position the depth slide on the outer input shaft.

- The Ruler (2 pc.) - T40100- lies straight across the transmission flange over the end of the shaft.

> **Caution**
>
> There is the risk of incorrect measurements.
>
> - The Ruler (2 pc.) - T40100- should stay in this position for the following measurements. Do not move it or take if off.

- Set the depth gauge to “0”.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/d13eab184ebdee27.webp)

- Position the depth slide on the Gauge - Clutch Bearings - T10466-, as illustrated.
- Measure dimension “A 2a ” on the Gauge - Clutch Bearings - T10466-.

- Example: dimension “A 2a ” = 4.79 mm

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/2d22000b9a942315.webp)

- Measure dimension “A 2b ” on the other side of the Gauge - Clutch Bearings - T10466-.

- Example: dimension “A 2b ” = 4.75 mm

- Calculate the average value from dimension “A 2a ” and “A 2b ”.
  Formula: (A 2a + A 2b) / 2

Example:

- (4.79 + 4.75) / 2 = 4.77 mm
- Result: dimension “A 2” = 4.77 mm

Step 7: Determine the Height Tolerance for the “K 2” Clutch Engaging Bearing.

> **Note**
>
> Using dimension “A 2” and dimension “B”, calculate the height tolerance for clutch “K 2” engaging bearing as follows:

|  | Dimension “A 2” |
| --- | --- |
| – | Dimension “B” |
| = | Height tolerance for clutch “K 2” engaging bearing |

Example:

- 4.77 mm - 2.60 mm = 2.17 mm
- Result: height tolerance for clutch “K 2” engaging bearing = 2.17 mm 

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/08cd9c146ae840cf.webp)

Step 8: Determine the Clutch Tolerance for the “K 2” Clutch.

- Read the clutch tolerance value on the new clutch.

- Example: clutch tolerance read on the clutch “K 2 = – 0.2”, as illustrated.

Step 9: Determine the “SK 2” Shim Thickness.

> **Note**
>
> Using the clutch tolerance of clutch “K 2”, now the thickness of shim “SK 2” can be calculated as follows:

|  | Height tolerance for the engaging bearing “K 2” |
| --- | --- |
| –/+ | Clutch tolerance for the clutch “K 2” |
| = | Calculated thickness for shim “SK 2” |

Example:

- 2.17 mm – 0.20 mm = 1.97 mm
- Result: calculated shim thickness “SK 2” = 1.97 mm

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/3917e2676de9735c.webp)

- Measure the needed shim from the shims supplied and keep it close for installation.

| Calculated Shim Thickness mm | Available Shim Thicknesses in mm |
| --- | --- |
| 0.31 to 0.90 | 0.80 |
| 0.91 to 1.10 | 1.00 |
| 1.11 to 1.30 | 1.20 |
| 1.31 to 1.50 | 1.40 |
| 1.51 to 1.70 | 1.60 |
| 1.71 to 1.90 | 1.80 |
| 1.91 to 2.10 | 2.00 |
| 2.11 to 2.30 | 2.20 |
| 2.31 to 2.50 | 2.40 |
| 2.51 to 2.70 | 2.60 |
| 2.71 to 3.30 | 2.80 |

Example:

- Result: calculated shim thickness “SK 2” = 1.97 mm
- Selected shim thickness = 2.00 mm

> **Warning**
>
> Only install these shims later to avoid damaging the clutch.
>
> The adjustment is now complete and the »small« engaging lever is already installed. The next step is to reinstall the clutch.

- Install the clutch. Refer to [⇒ 2.4 Dual Clutch, Installing, Transmission Production Date from 06/2011](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/dual-clutch-installing-from-06-2011/#t62-82).

## Tightening torques on this page

### Torque
| Item | Part | Torque | Notes |
| --- | --- | --- | --- |
| 9 | Bolts | 8 Nm +90° | Always replace after removing |
