# 1.2 Dual Clutch, Removing, through Transmission Production Date 05/2011 – 7-speed DSG gearbox 0AM (DQ200)

> VW Polo 6R/6C, step by step: removing dual clutch, DSG 0AM built up to 05/2011 – 16 steps, special tools 3438, T10323 and T10356/5 and 12 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/dual-clutch-removing-up-to-05-2011/
- Original document: https://cdn.polo.blue/files/7-speed_dual_clutch_transmission_0am-eng.pdf
- 30 – Clutch, [7-speed DSG gearbox 0AM (DQ200)](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/index.md)
- Previous procedure: [1.1 Overview – Dual Clutch, through Transmission Production Date 05/2011](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/dual-clutch-overview-up-to-05-2011/index.md)
- Next procedure: [1.3 “K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date through 05/2011](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/k1-k2-engaging-bearing-position-adjusting-up-to-05-2011/index.md)

Special tools and workshop equipment required

- T-Handle Hook - 3438-
- Support Bridge - T10323-
- -T10356/5- from the Subframe Bushing Assembly Tool Kit - T10356-
- Puller - Clutch - T10373-
- Clutch Press Piece - T10376-
- Engine Bung Set - VAS6122-

- Remove the transmission:

- Refer to
- Refer to [⇒ 5 Transmission, Removing and Installing, Jetta from MY 2011](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/34-controls-housing/)
- The DSG Transmission Mechatronic - J743- is installed in the transmission.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/ecba26be1dfbf7f2.webp)

- Remove both caps -arrows- and seal with suitable oil-tight plugs from the Engine Bung Set - VAS6122- for example.

> **Caution**
>
> On some transmissions, the breather cap on the Mechatronic is destroyed during removal and must be replaced.

Checking the hydraulic fluid level for the Mechatronic is not possible. The Mechatronic vent must be sealed oil-tight before performing any assembly work.

Fluid that has leaked out of the Mechatronic hydraulic area may not be refilled or checked. Replace the Mechatronic if fluid is leaking.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/d5a5a052f0def3d6.webp)

Turn the transmission on the engine/transmission holder with the clutch facing up.

Refer to [⇒ 6 Transmission, Transporting and Securing To Assembly Stand](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/34-controls-housing/transmission-transporting-securing-assembly-stand/#t195-89) for information on securely transporting the transmission and securing to the assembly stand.

> **Note**
>
> The dual clutch is removed upward. The Mechatronic stays on the transmission.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/77f9e31122375bcb.webp)

- Remove the locking ring -arrow- from the hub.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/9c90177d17c3633e.webp)

- Remove the hub using T-Handle Hook - 3438- and a screwdriver.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/2c55da5333ba15cb.webp)

- Remove the locking ring -arrow- from the clutch.

If it is Not Possible to Remove the Locking Ring:

> **Note**
>
> - The clutch is »jamming« the circlip from underneath if the circlip cannot be removed.
> - If this is the case, then push the clutch slightly down and this will release the pressure on the locking ring. Never hit the clutch or the shaft with a hammer.
> - Always replace the locking ring.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/03dff32d0fee921a.webp)

- Position the Support Bridge - T1032- parallel to the transmission flange, as illustrated.
- If necessary, even out the gaps with Assembly Tool - 5 - T10356A/5- for example.
- Tighten the bolts -A- hand-tight.

> **Note**
>
> Secure the bolts -A- with a nut, if needed.

> **Caution**
>
> Danger of damaging the clutch and other components.
>
> - Push the clutch down gently without pressing.

- Turn the spindle against the Clutch Press Piece - T10376- to lower it.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/8beb2d5d1a267cc3.webp)

- Remove the special tool and remove the circlip -arrow- for the clutch.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/e5ecc592be14ee42.webp)

Continuation for Removing the Locking Ring:

- Insert the Puller - Clutch - T10373- into the clutch and remove the clutch.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/7a4c30a2bfc9ebf2.webp)

- Remove the clutch together with the Puller - Clutch - T10373-.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/b216853392850c43.webp)

- Remove the small engaging bearing.
- Remove the large engaging lever.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/a519c29d1722f938.webp)

- Remove the bolts and remove the engaging lever with the bracket.

> **Note**
>
> Only a few »older« transmissions do not have a bracket.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/efd9b4ba374f5205.webp)

- Remove the engaging lever mount.

Before installing the clutch, check if the »clutch needs to be adjusted or not during assembly«. Refer to [⇒ 1.3 K 1 and K 2 Clutch Engaging Bearing Position, Adjusting, Transmission Production Date through 05/2011](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/k1-k2-engaging-bearing-position-adjusting-up-to-05-2011/#t24-531).

Adjusting. Refer to [⇒ 1.3 K 1 and K 2 Clutch Engaging Bearing Position, Adjusting, Transmission Production Date through 05/2011](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/k1-k2-engaging-bearing-position-adjusting-up-to-05-2011/#t24-531)

Install the Dual Clutch. Refer to [⇒ 1.4 Dual Clutch, Installing, Transmission Production Date through 05/2011](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/dual-clutch-installing-up-to-05-2011/#t37-82).
