# 2.2 Dual Clutch, Removing, Transmission Production Date from 06/2011 – 7-speed DSG gearbox 0AM (DQ200)

> VW Polo 6R/6C, step by step: removing dual clutch, DSG 0AM built from 06/2011 – 14 steps, special tools 3438, VAS6122 and T10323 and 12 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/dual-clutch-removing-from-06-2011/
- Original document: https://cdn.polo.blue/files/7-speed_dual_clutch_transmission_0am-eng.pdf
- 30 – Clutch, [7-speed DSG gearbox 0AM (DQ200)](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/index.md)
- Previous procedure: [2.1 Overview – Dual Clutch, Transmission Production Date from 06/2011](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/dual-clutch-overview-from-06-2011/index.md)
- Next procedure: [2.3 “K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/k1-k2-engaging-bearing-position-adjusting-from-06-2011/index.md)

Special tools and workshop equipment required

- T-Handle Hook - 3438-
- Engine Bung Set - VAS6122-
- Support Bridge - T10323-
- -T10356/5- from the Subframe Bushing Assembly Tool Kit - T10356-
- Puller - Clutch - T10373-
- Clutch Press Piece - T10376-

**Requirement**

- The transmission is removed and mounted to the engine/transmission holder. Refer to [⇒ 6 Transmission, Transporting and Securing To Assembly Stand](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/34-controls-housing/transmission-transporting-securing-assembly-stand/#t195-89).
- The DSG Transmission Mechatronic - J743- is installed in the transmission.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/c75e83cb9b722d74.webp)

- Remove both breather caps -arrows- and seal with clean oiltight plugs from the Engine Bung Set - VAS6122- for example.

> **Caution**
>
> The vent cap on the Mechatronic will be destroyed during removal and must be replaced.

Checking the hydraulic fluid level for the Mechatronic is not possible. The Mechatronic vent must be sealed oil-tight before performing any assembly work.

Fluid that has leaked out of the Mechatronic hydraulic area may not be refilled or checked. Replace the Mechatronic if fluid is leaking.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/d5a5a052f0def3d6.webp)

- Turn the transmission on the engine/transmission holder with the clutch facing up.

> **Note**
>
> The clutch is removed upward. The Mechatronic stays on the transmission.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/77f9e31122375bcb.webp)

- Remove the circlip on the hub -arrow-.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/76fa0a76d1884a79.webp)

- Remove the hub using T-Handle Hook - 3438- and a screwdriver.

> **Note**
>
> The position of the “K 1” and “K 2” engaging bearings must be adjusted later when clutch components are replaced. It is advisable to determine dimension “B” for the measurements. Refer to [⇒ 2.3 K 1 and K 2 Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/k1-k2-engaging-bearing-position-adjusting-from-06-2011/#t49-531). 

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/8beb2d5d1a267cc3.webp)

- Remove the circlip -arrow- for the clutch.

If It Is Not Possible to Remove the Locking Ring

> **Note**
>
> - The clutch is »jamming« the circlip from underneath if the circlip cannot be removed.
> - If this is the case, press the clutch downward as described in the following. The circlip will then be relieved. Never hit the clutch or the shaft with a hammer.
> - Always replace the locking ring.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/03dff32d0fee921a.webp)

- Position the Support Bridge - T1032- parallel to the transmission flange, as illustrated.
- If necessary, even out the gaps with Assembly Tool - 5 - T10356A/5- for example.
- Tighten the bolts -A- hand-tight.

> **Note**
>
> Secure the bolts -A- with a nut, if needed.

> **Caution**
>
> Danger of damaging the clutch and other components.
>
> - Push the clutch down gently without pressing.

- Turn the spindle against the Clutch Press Piece - T10376- to lower it.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/8beb2d5d1a267cc3.webp)

- Remove the locking ring -arrow- from the clutch.

> **Warning**
>
> Do not re-use the locking ring.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/e5ecc592be14ee42.webp)

Continuation for Removing the Locking Ring

- Insert the Puller - Clutch - T10373- into the clutch and remove the clutch.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/7a4c30a2bfc9ebf2.webp)

- Remove the clutch together with the Puller - Clutch - T10373-.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/9795e4df7e816005.webp)

- Remove the »large« engaging lever with the »small« engaging bearing.

> **Note**
>
> The guide sleeve upper section cannot be removed or installed separately. It is always removed and installed together with the guide sleeve lower section and the »small« engaging lever.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/f19408c4aa367aed.webp)

- Remove the bolts and the »small« engaging lever with the guide sleeve upper and lower sections.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/7f0b56d382174997.webp)

The ball stud -2- remains installed if no components are replaced.

The engaging lever support -1- is not removed.

> **Note**
>
> If dimension “B” was already measured, then step “2” of the measurement can be made now. Refer to [⇒ 2.3 “K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/k1-k2-engaging-bearing-position-adjusting-from-06-2011/#t54-231).
