# 1.4 Dual Clutch, Installing, Transmission Production Date through 05/2011 – 7-speed DSG gearbox 0AM (DQ200)

> VW Polo 6R/6C, step by step: installing dual clutch, DSG 0AM built up to 05/2011 – 22 steps. Only a few »older« transmissions do not have a bracket.

- Web page: https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/dual-clutch-installing-up-to-05-2011/
- Original document: https://cdn.polo.blue/files/7-speed_dual_clutch_transmission_0am-eng.pdf
- 30 – Clutch, [7-speed DSG gearbox 0AM (DQ200)](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/index.md)
- Previous procedure: [1.3 “K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date through 05/2011](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/k1-k2-engaging-bearing-position-adjusting-up-to-05-2011/index.md)
- Next procedure: [2 Dual Clutch, Removing and Installing, from Transmission Production Date 06/2011](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/dual-clutch-removing-installing-from-06-2011/index.md)

Special tools and workshop equipment required

- Support Bridge - T10323-
- -T10356/5- from the Subframe Bushing Assembly Tool Kit - T10356-
- Puller - Clutch - T10373-
- Clutch Press Piece - T10376-
- Adhesive - AMV 195 KD1 01-
- Tightening specifications. Refer to [⇒ 1.1 Overview - Dual Clutch, through Transmission Production Date 05/2011](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/dual-clutch-overview-up-to-05-2011/#t19-380).

> **Caution**
>
> The following components must also be replaced if the dual clutch is replaced:
>
> - Both engaging levers with engaging bearing.
> - Engaging lever mount.
> - Engaging bearing shims.

When replacing the dual clutch and its components, the “K 1 and K 2” engaging bearing position must always be readjusted. Refer to [⇒ 1.3 K 1 and K 2 Clutch Engaging Bearing Position, Adjusting, Transmission Production Date through 05/2011](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/k1-k2-engaging-bearing-position-adjusting-up-to-05-2011/#t24-531).

> **Note**
>
> - Clutch components must have no oil or grease on them when being installed.
> - Replace all bolts that were tightened with an additional turn.
> - The following four steps are only necessary if the engaging bearing position did not need to be adjusted.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/efd9b4ba374f5205.webp)

- Insert the engaging lever mount.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/f1dff508c7e1cd70.webp)

- Install the small engaging lever with the bracket.

> **Note**
>
> Only a few »older« transmissions do not have a bracket.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/faddc664cd548236.webp)

- Tighten the small engaging lever with two new bolts.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/39701f072b78995e.webp)

- Install the large engaging lever.
- Make sure both engaging levers fit correctly.

> **Caution**
>
> Danger of damaging the dual clutch and other components.
>
> - The position of the engaging bearings must be adjusted correctly.

Adjusting the engaging bearings can only be performed prior to installing the dual clutch.

The position of the engaging bearing must be adjusted after completing the following:

- The dual clutch was replaced.
- The engaging levers were replaced.
- The engaging lever mount was replaced.
- The engaging bearings were replaced.

It is necessary to adjust the position of the “K 1 and K 2” engaging bearings first if one of the above mentioned procedures was performed and the readjusted shim is inserted. Refer to [⇒ 1.3 K 1 and K 2 Clutch Engaging Bearing Position, Adjusting, Transmission Production Date through 05/2011](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/k1-k2-engaging-bearing-position-adjusting-up-to-05-2011/#t24-531).

Continue with assembling only when the adjustment is correct.

The removed shims can be used again if no new parts were installed.

Only one shim per engaging bearing can be inserted for the adjustment.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/89bac64cb05e2718.webp)

- Insert the small engaging bearing -1- with the measured shim -2- for the “K 2” clutch.

The Shim Belongs Under the Small Engaging Bearing. Install the Shim First.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/084344d30e971a1b.webp)

- The small engaging bearing fits in only one position due to the 4 grooves.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/c7eabef97f11c3e5.webp)

- Turn the engaging bearing in direction of -arrows- to make sure it is installed correctly and fits correctly in the grooves.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/2493cf6ada05f108.webp)

- Secure the »large« shim -1- for the “K 1” clutch with three drops of Adhesive - AMV 195 KD1 01- -arrows-.

This prevents the shim from sliding out of its position when inserting the clutch.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/c86fb8cdeddaa146.webp)

- Turn back the spindle on the Puller - Clutch - T10373-.

> **Caution**
>
> Danger of causing damage to the clutch adjusting tool.
>
> - The clutch is self-adjusting. Vibrations can affect the adjusting tool. Be careful not to drop the clutch into the transmission when installing.

- Install the clutch in the transmission using the Puller - Clutch - T10373- as shown.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/751ff8f01f5f7535.webp)

- Position the Support Bridge - T1032- parallel to the transmission flange, as illustrated.
- If necessary, even out the gaps using, for example, -T10356/5- from the Assembly Tool - T10356A-.
- Tighten the bolts -A- hand-tight.

> **Note**
>
> Secure the bolts -A- with a nut, if needed.

- Install the clutch all the way.

> **Note**
>
> Keep on hand on the clutch while pressing it on. A slight »vibrating« can be felt. Vibrating means the clutch is being pushed onto its press-fit. It can also be felt when the clutch has reached its stop.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/4e69f9ca36cb5a6d.webp)

- Hold the new locking ring with locking ring pliers, as illustrated.

- Installed position: narrow ends of the locking ring at the top.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/a8e6f9ddeffe41ff.webp)

- Install the circlip -arrow-

> **Note**
>
> The clutch is not pressed correctly on the stop if the locking ring cannot be installed.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/d28c2a7ed5487721.webp)

- Turn the clutch against the Puller - Clutch - T10373- by hand without using any other tools so that it can move into its operating position in direction of -arrow-.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/5df8bdb597b32da9.webp)

> **Note**
>
> - The clutch sits on the stop at the bottom of the input shaft. This is not its optimal position.
> - The clutch should be pulled up just far enough until it touches the locking ring.

> **Note**
>
> Only turn it by hand. This way the clutch slides against the locking ring. Do not use any other tool.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/2e6a0a250f9d5ed1.webp)

- Install the hub.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/abf8757c1578e7b3.webp)

- The hub as a single »large tooth« -arrow- and fits in only one position.
- The »large tooth« has a marking -arrow- on the engine side.
  огромный архив документации по автомобилям Volkswagen, Skoda, Seat, Audi 

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/66290af7da20da7d.webp)

- Insert the locking ring -arrow-.

- The end of the locking ring must face the »nose« on the clutch.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/40b3755a53844f1e.webp)

- Turn the clutch by hand and pay attention to the small engaging lever when turning.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/2f72b9698a54cd65.webp)

- The small engaging lever must not move at all when turning the clutch. It must not move back and forth.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/235f6c37d4939c70.webp)

> **Note**
>
> - If an engaging lever is moving back and forth, then the shim is not in its correct position.
> - In this case, remove the clutch again. Refer to [⇒ 1.2 Dual Clutch, Removing, through Transmission Production Date 05/2011](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/dual-clutch-removing-up-to-05-2011/#t21-166).
> - Check the shims -arrows-.
> - The shims must fit correctly and must not be damaged.
> - It is possible there was a calculation error. Check the measurements one more time. Refer to [⇒ 1.3 K 1 and K 2 Clutch Engaging Bearing Position, Adjusting, Transmission Production Date through 05/2011](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/k1-k2-engaging-bearing-position-adjusting-up-to-05-2011/#t24-531).

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/99664dea440bd47e.webp)

- Remove the plugs and mount both breather caps -arrowsagain.

> **Caution**
>
> On some transmissions, the breather cap on the Mechatronic is destroyed during removal and must be replaced.

- After installing the transmission, perform the Complete basic setting using Guided Functions in the Vehicle Diagnostic Tester.
