# 2.4 Dual Clutch, Installing, Transmission Production Date from 06/2011 – 7-speed DSG gearbox 0AM (DQ200)

> VW Polo 6R/6C, step by step: installing dual clutch, DSG 0AM built from 06/2011 – 18 steps, special tools T10323, T10356/5 and T10356 and 15 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/dual-clutch-installing-from-06-2011/
- Original document: https://cdn.polo.blue/files/7-speed_dual_clutch_transmission_0am-eng.pdf
- 30 – Clutch, [7-speed DSG gearbox 0AM (DQ200)](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/index.md)
- Previous procedure: [2.3 “K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/k1-k2-engaging-bearing-position-adjusting-from-06-2011/index.md)
- Next procedure: [3 Clutch-Side Seals, Removing and Installing](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/clutch-side-seals-removing-and-installing/index.md)

Special tools and workshop equipment required

- Support Bridge - T10323-
- -T10356/5- from the Subframe Bushing Assembly Tool Kit - T10356-
- Puller - Clutch - T10373-
- Clutch Press Piece - T10376-

**Installing**

> **Caution**
>
> The following components must also be replaced if the dual clutch is replaced:
>
> - Both engaging levers with engaging bearing.
> - Ball stud for the “K 2” engaging lever.
> - Engaging bearing shims.

The hinge mount cannot be removed.

When replacing the dual clutch and its components, the “K 1 and K 2” engaging bearing position must always be readjusted. Refer to [⇒ 2.3 K 1 and K 2 Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/k1-k2-engaging-bearing-position-adjusting-from-06-2011/#t49-531).

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/2d1018a1fb6ee26e.webp)

The engaging lever support -1- and ball stud -2- are installed.

> **Note**
>
> - Replace all bolts that were tightened with an additional turn.
> - The guide sleeve upper section cannot be removed or installed separately. It is always removed and installed together with the guide sleeve lower section and the »small« engaging lever.

The Following Procedure Is Only Then Necessary If All of the Components Mentioned are Removed and Reinstalled.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/aa5c1f3f0636fa9c.webp)

- Install the »small« engaging lever with the upper and lower sections of the guide sleeve. Install new bolts and tighten them.

Tightening specification. Refer to [⇒ 2.3 “K 1” and “K 2” Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/k1-k2-engaging-bearing-position-adjusting-from-06-2011/#t51-206).

**Continuation for All**

> **Caution**
>
> Danger of damaging the dual clutch and other components.
>
> - The position of the engaging bearings must be adjusted correctly.

Adjusting the engaging bearings can only be performed prior to installing the dual clutch.

Continue with assembling only when the adjustment is correct.

The removed shims can be used again if no new parts were installed.

Only one shim per engaging bearing can be inserted for the adjustment.

- Clutch components must have no oil or grease on them when being installed.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/6ce617291581de79.webp)

- Install the »large« engaging lever with the measured shims for “K 1” and “K 2” and with the small engaging bearing.

> **Note**
>
> - The large shim in the large engaging bearing with the halfround side facing down.
> - The small shim belongs under the small engaging bearing. Install the shim first.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/5b89f17f8ef04ba7.webp)

The shim and the small engaging bearing fit only in one position due to the 8 grooves.

- Turn and make sure the parts are installed correctly and fit correctly in the grooves.
- Make sure both engaging levers fit correctly.
- Turn back the Puller - Clutch - T10373- spindle.

> **Caution**
>
> Danger of causing damage to the clutch adjusting tool.
>
> - The clutch is self-adjusting. Vibrations can affect the adjusting tool. Be careful not to drop the clutch into the transmission when installing.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/c86fb8cdeddaa146.webp)

- Install the clutch in the transmission using the Puller - Clutch - T10373- as shown.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/751ff8f01f5f7535.webp)

- Position the Support Bridge - T1032- parallel to the transmission flange, as illustrated.
- If necessary, even out the gaps using, for example, -T10356/5- from the Assembly Tool - T10356A-.
- Tighten the bolts -A- hand-tight.

> **Note**
>
> Secure the bolts -A- with a nut, if needed.

- Install the clutch all the way.

> **Note**
>
> Keep on hand on the clutch while pressing it on. A slight »vibrating« can be felt. Vibrating means the clutch is being pushed onto its press-fit. It can also be felt when the clutch has reached its stop.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/d8586e49c7736806.webp)

- Hold the new locking ring with locking ring pliers, as illustrated.

- Installed position: narrow ends of the locking ring at the top.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/2c55da5333ba15cb.webp)

- Install the circlip -arrow-

> **Note**
>
> The clutch is not pressed correctly on the stop if the locking ring cannot be installed.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/d28c2a7ed5487721.webp)

- Turn the clutch against the Puller - Clutch - T10373- by hand without using any other tools so that it can move into its operating position in direction of -arrow-.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/5df8bdb597b32da9.webp)

> **Note**
>
> - The clutch sits on the stop at the bottom of the input shaft. This is not its optimal position.
> - The clutch should be pulled up just far enough until it touches the locking ring.

> **Note**
>
> Only turn it by hand. This way the clutch slides against the locking ring. Do not use any other tool.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/2e6a0a250f9d5ed1.webp)

- Install the hub.

- The hub as a single »large tooth« -arrow- and fits in only one position.
- The »large tooth« has a marking on the engine side.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/77f9e31122375bcb.webp)

- Insert the locking ring -arrow-.

- The end of the locking ring must face the »nose« on the clutch.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/9e45265b70829060.webp)

- Turn the clutch by hand. It should turn without any problem.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/0195240281256052.webp)

> **Note**
>
> - Remove the clutch if it is difficult to turn or if the it grinds against the clutch plates while being turned. Refer to [⇒ 2.2 Dual Clutch, Removing, Transmission Production Date from 06/2011](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/dual-clutch-removing-from-06-2011/#t46-281).
> - Check the installed position of the shims -arrows-.
> - The shims must fit correctly and must not be damaged. Refer to [⇒ 2.4 Dual Clutch, Installing, Transmission Production Date from 06/2011](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/dual-clutch-installing-from-06-2011/#t62-82).
> - It is possible there was a calculation error. Check the measurements one more time. Refer to [⇒ 2.3 K 1 and K 2 Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/k1-k2-engaging-bearing-position-adjusting-from-06-2011/#t49-531).
> - If there is no error, then it is possible the clutch shifted during transportation/assembly. In this case it is necessary to install a new clutch. Then it is necessary to adjust the position of the engaging bearing again. Refer to [⇒ 2.3 K 1 and K 2 Clutch Engaging Bearing Position, Adjusting, Transmission Production Date from 06/2011](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/30-clutch/k1-k2-engaging-bearing-position-adjusting-from-06-2011/#t49-531).

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/99664dea440bd47e.webp)

- Remove both plugs and mount the vent caps -arrows-.

> **Warning**
>
> The vent cap on the Mechatronic will be destroyed during removal and must be replaced.

- After installing the transmission, perform the Complete basic setting using Guided Functions in the Vehicle Diagnostic Tester.
  огромный архив документации по автомобилям Volkswagen, Skoda, Seat, Audi
