# 7.2 Transmission – 7-speed DSG gearbox 0AM (DQ200)

> VW Polo 6R/6C (General Repair Information), step by step: DSG 0AM repair rules: gearbox, seals, bolts, static – 2 steps, tightening torques and 6 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/00-general-technical-data/transmission/
- Original document: https://cdn.polo.blue/files/7-speed_dual_clutch_transmission_0am-eng.pdf
- 00 – General, Technical Data, [7-speed DSG gearbox 0AM (DQ200)](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/index.md)
- Previous procedure: [7.1 Tools](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/00-general-technical-data/tools/index.md)
- Next procedure: [7.3 Working with Vehicle Diagnostic Testers](https://catalog.polo.blue/repair-manuals/dsg-gearbox-0am-dq200/00-general-technical-data/working-with-vehicle-diagnostic-testers/index.md)

The flywheel transfers the engine torque to the dual clutch. The flywheel and the dual clutch are connected to each other via splines. Together they take over the function of the dual mass flywheel.

The transmission is built like a 7-speed manual transmission. The alternating hydraulic actuation of the two dry multi-plate clutches permits operation similar to that of an automatic transmission. This means the gears are automatically or manually shifted via the Tiptronic mode. There is no clutch pedal.

The transmission has an opening in the housing.

> **Note**
>
> This opening is sealed with a cap on some transmissions.

- Make sure that no small pieces fall into this opening -arrowduring assembly work. Cover the opening with a cloth.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/c3b5fdff2e330d32.webp)

Always make sure that no dirt enters an »open« transmission.

- Do not run the engine when the cover is removed from the transmission or when there is no transmission fluid in the transmission. Do not tow the vehicle.
- Thoroughly clean the connection points and the area around them first, and then loosen them.
- Make sure that the alignment sleeves between the engine and transmission are positioned correctly when installing the transmission.
- Place the removed parts on a clean surface and cover them so that they do not become contaminated. Use foil and paper. Only use lint-free cloths.
- Only install clean components. Install replacement parts immediately after removing them from their packaging.
- Cover all opened components carefully if it necessary to perform a repair.

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/f182beadde18d64d.webp)

Some Vehicles Have A Cover Over the Engaging Levers

The cover prevents dirt from getting in.

Tightening specification for bolts: 8 Nm

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/e6d846ad85b07169.webp)

**Overview - Transmission**

- **1** Transmission ventilation cap
- **2** Cover
- **3** Selector Lever
- **4** DSG Transmission Mechatronic - J743- Bleed Unit
- **5** DSG Transmission Mechatronic - J743-
- **6** Dual Clutch
- **7** Flange Shaft
- **8** Oil Drain Plug, 30 Nm
- **9** S tronic Transmission 

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/5f102172e7335a3b.webp)

**Selector Mechanism**

Similar to an automatic transmission, the selector lever position is no longer transmitted mechanically to the transmission via the selector lever cable and the multifunction transmission range switch (drive position sensor). The selector lever positions and shifts are transmitted via a separate control module in the selector mechanism to the transmission control module via the CAN bus. Shifting occurs without a selector lever cable. The selector lever cable mechanically brings the parking lock into the selector lever position “P”.

**Transmission Fluid**

Only transmission fluids available as replacement part may be used for the DSG® transmission 0AM. Using other oils can lead to function problems or can even cause the transmission to fail, for the specification. Refer to the Parts Catalog.

It is not possible to check the transmission fluid level in the transmission. A transmission fluid level adjustment can only be done when replacing the transmission fluid.

Do not reuse drained oil.

> **Caution**
>
> Be very careful when handling transmission fluid. Dispose of drained transmission fluid correctly.

**O-Rings, Gaskets and Seals **

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/07d6745f2408cdc8.webp)

- O-rings, gaskets and seals must always be replaced.
- The seals for the stub shaft or the flange shaft and drive axle are also called shaft seals.
- After removing seal rings and seals, always inspect the contact surfaces at housing or shaft for burrs resulting from removal, or for other signs of damage.
- Before installing the seals, lightly oil the outer circumference and fill the space between the sealing lips -arrow- halfway with Grease - G 052 128 A1-.
- The open side of the gaskets point toward the fluid to be sealed in.
- Coat the O-rings with transmission fluid or Vaseline before inserting to prevent them from being crushed during assembly.
- Do not use any other lubricants in the transmission fluid area. Otherwise there is a danger of the hydraulic transmission control malfunctioning.

**Circlips**

- Do not stretch the circlips.
- Replace damaged or stretched circlips.
- The circlips must rest at the bottom of the groove.

**Bolts and Nuts**

- Loosen or tighten bolts and nuts on the covers or housings diagonally.
- The tightening specifications given apply to unoiled bolts and nuts.
- Use a wire brush to clean the threads of the bolts that were installed with locking fluid. Install the bolts with Locking Fluid - AMV 185 101 A1-.
- Clean the threaded holes for the self-locking bolts or for the bolts coated with locking fluid (for example with a thread tap). Otherwise there is the risk that the bolts could break off the next time they are removed.
- Always replace self-locking bolts and nuts. 

![](https://catalog.polo.blue/manuals/vw-polo-gearbox-0am-dsg/a6ac8952cc1e9e28.webp)

**Electrical Components**

Due to an electrostatic charge to the human body, a person can receive an electrostatic shock when metal objects are touched.

This charge can damage the electrical/electronic components on the transmission and the selector mechanism.

- Touch a grounded object, such as, a water pipe or a vehicle hoist, before working on electrical/electronic components. Do not touch connector or »open« electronic components directly.

## Tightening torques on this page

### In the steps
| Step | Torque |
| --- | --- |
| Tightening specification for bolts: 8 Nm | 8 Nm |

### Torque
| Item | Part | Torque |
| --- | --- | --- |
| 8 | Oil Drain Plug | 30 Nm |
