# Tightening torques – Brake systems

> Every tightening torque the Brake systems manual gives for the VW Polo 6R, by repair group and procedure. Each one links to its drawing or table in the procedure.

- Web page: https://catalog.polo.blue/repair-manuals/brake-systems/torques/
- Original document: https://cdn.polo.blue/files/vw-polo-5-2010-brake-systems-eng.pdf
- [Brake systems](https://catalog.polo.blue/repair-manuals/brake-systems/index.md)

## 45 – Anti-lock brake system

### [6.1 Bosch 8.2; 9.0 ABS, LHD vehicles](https://catalog.polo.blue/repair-manuals/brake-systems/45-anti-lock-brake-system/bosch-8-2-9-0-abs-lhd-vehicles/index.md)

#### Torque
| Item | Part | Torque | Notes |
| --- | --- | --- | --- |
| 11 | Self-locking hexagon nut | 25 Nm |  |
| 13 | Self-locking hexagon nut | 25 Nm |  |
| 20 | Self-locking hexagon nut | 20 Nm |  |
| 22 | Pin | 8 Nm | For Bosch 8.2 ABS · Bolt and washer assembly for Bosch 9.0 ABS, 8 Nm |

#### 6.1.4 Installing new control unit [To the steps](https://catalog.polo.blue/repair-manuals/brake-systems/45-anti-lock-brake-system/bosch-8-2-9-0-abs-lhd-vehicles/#6-1-4-installing-new-control-unit)
| Step | Torque |
| --- | --- |
| Use new bolts! Stage 1: position and centre control unit; screw in - Torx bolts until Torx bolts contact housing. Stage 2: Seat sealing lugs evenly on all sides and 1.5 to tighten initially. | 2 Nm |
| Stage 3: Final tightening to specified torque. 3 Nm | 3 Nm |

#### 6.1.5 Installing control unit and hydraulic unit [To the steps](https://catalog.polo.blue/repair-manuals/brake-systems/45-anti-lock-brake-system/bosch-8-2-9-0-abs-lhd-vehicles/#6-1-5-installing-control-unit-and-hydraulic-unit)
| Step | Torque |
| --- | --- |
| Pin to hydraulic unit | 8 Nm |
| Hexagon nut to body | 20 Nm |
| Brake lines to ABS unit: Thread M10 x 1 | 14 Nm |
| Thread M12 x 1 | 14 Nm |

### [6.2 Bosch 8.2; 9.0 ABS, RHD vehicles](https://catalog.polo.blue/repair-manuals/brake-systems/45-anti-lock-brake-system/bosch-8-2-9-0-abs-rhd-vehicles/index.md)

#### Torque
| Item | Part | Torque | Notes |
| --- | --- | --- | --- |
| 2 | Brake line | 14 Nm | ABS hydraulic unit - N55- to rear right brake caliper/wheel brake cylinder. · Marked on hydraulic unit with -HR-. |
| 3 | Brake line | 14 Nm | ABS hydraulic unit - N55- to rear left brake caliper/wheel brake cylinder. · Marking on ABS hydraulic unit - N55- -HL- |
| 4 | Brake line | 14 Nm | ABS hydraulic unit - N55- to front right brake caliper. · Marking on ABS hydraulic unit - N55- -VR- |
| 7 | Brake line | 14 Nm | ABS hydraulic unit - N55- to front left brake caliper. · Marking on ABS hydraulic unit - N55- -VL- |
| 8 | Brake line | 14 Nm | ABS hydraulic unit - N55- to brake master cylinder/secondary piston circuit · Marking on ABS hydraulic unit - N55- -HZ2- |
| 9 | Brake line | 14 Nm | ABS hydraulic unit - N55- to brake master cylinder/secondary piston circuit · Marking on ABS hydraulic unit - N55- -HZ1- |
| 12 | Nut | 20 Nm | Qty. 3 · Always renew after removing. |
| 13 | Pin | 8 Nm | For Bosch 8.2 ABS · Bolt and washer assembly for Bosch 9.0 ABS, 8 Nm |

#### 6.2.4 Installing new control unit [To the steps](https://catalog.polo.blue/repair-manuals/brake-systems/45-anti-lock-brake-system/bosch-8-2-9-0-abs-rhd-vehicles/#6-2-4-installing-new-control-unit)
| Step | Torque |
| --- | --- |
| Use new bolts! Stage 1: position and centre control unit; screw in - Torx bolts until Torx bolts contact housing. Stage 2: Seat sealing lugs evenly on all sides and 1.5 to tighten initially. | 2 Nm |
| Stage 3: Final tightening to specified torque. 3 Nm | 3 Nm |

#### 6.2.5 Installing control unit and hydraulic unit [To the table](https://catalog.polo.blue/repair-manuals/brake-systems/45-anti-lock-brake-system/bosch-8-2-9-0-abs-rhd-vehicles/#6-2-5-installing-control-unit-and-hydraulic-unit)
| Part | Torque |
| --- | --- |
| Brake lines to ABS hydraulic unit - N55- Thread M10 x 1 | 14 Nm |
| Thread M12 x 1 | 14 Nm |
| Bracket to body | 20 Nm |

### [6.3 Bosch 8.2i; 9.0i ABS/EDL/TCS/ESP, LHD vehicles](https://catalog.polo.blue/repair-manuals/brake-systems/45-anti-lock-brake-system/bosch-8-2i-9-0i-abs-edl-tcs-esp-lhd-vehicles/index.md)

#### Torque [To the drawing](https://catalog.polo.blue/repair-manuals/brake-systems/45-anti-lock-brake-system/bosch-8-2i-9-0i-abs-edl-tcs-esp-lhd-vehicles/#t39-462)
| Item | Part | Torque | Notes |
| --- | --- | --- | --- |
| 9 | Hexagon nut | 8 Nm | For 3 rubber damper mountings · 1 cap nut on side at top; it must be unscrewed to height of stud shoulder, otherwise removal and installation are not possible. |
| 12 | Self-locking hexagon nut | 25 Nm |  |
| 14 | Self-locking hexagon nut | 25 Nm |  |
| 21 | Self-locking hexagon nut | 20 Nm |  |
| 23 | Self-locking hexagon nut | 20 Nm |  |

#### 6.3.4 Installing new control unit [To the steps](https://catalog.polo.blue/repair-manuals/brake-systems/45-anti-lock-brake-system/bosch-8-2i-9-0i-abs-edl-tcs-esp-lhd-vehicles/#6-3-4-installing-new-control-unit)
| Step | Torque |
| --- | --- |
| Use new bolts! Stage 1: position and centre control unit; screw in - Torx bolts until Torx bolts contact housing. Stage 2: Seat sealing lugs evenly on all sides and 1.5 to tighten initially. | 2 Nm |
| Stage 3: Final tightening to specified torque. 3 Nm | 3 Nm |

#### 6.3.5 Installing control unit and hydraulic unit [To the steps](https://catalog.polo.blue/repair-manuals/brake-systems/45-anti-lock-brake-system/bosch-8-2i-9-0i-abs-edl-tcs-esp-lhd-vehicles/#6-3-5-installing-control-unit-and-hydraulic-unit)
| Step | Torque |
| --- | --- |
| Hexagon nut for rubber damper mounting 8 Nm Hexagon nut to body | 8 Nm |
| Hexagon nut for rubber damper mounting 8 Nm Hexagon nut to body | 20 Nm |
| Brake lines to ABS unit: Thread M10 x 1 | 14 Nm |
| Thread M12 x 1 | 14 Nm |

### [6.4 Bosch 8.2i; 9.0i ABS/EDL/TCS/ESP, RHD vehicles](https://catalog.polo.blue/repair-manuals/brake-systems/45-anti-lock-brake-system/bosch-8-2i-9-0i-abs-edl-tcs-esp-rhd-vehicles/index.md)

#### Torque
**All items:** Qty. 3

| Item | Part | Torque | Notes |
| --- | --- | --- | --- |
| 6 | Nut | 8 Nm | For rubber damper mounting · 1 cap nut on side at top; it must be unscrewed to height of stud shoulder, otherwise removal and installation are not possible. · 2 hexagon nuts with washer at bottom; turn back until rubber dampers can be turned. |
| 8 | Nut | 25 Nm | Always renew after removing. |

#### 6.4.4 Installing new control unit [To the steps](https://catalog.polo.blue/repair-manuals/brake-systems/45-anti-lock-brake-system/bosch-8-2i-9-0i-abs-edl-tcs-esp-rhd-vehicles/#6-4-4-installing-new-control-unit)
| Step | Torque |
| --- | --- |
| Use new bolts! Stage 1: position and centre control unit; screw in - Torx bolts until Torx bolts contact housing. Stage 2: Seat sealing lugs evenly on all sides and 1.5 to tighten initially. | 2 Nm |
| Stage 3: Final tightening to specified torque. 3 Nm | 3 Nm |

#### 6.4.5 Installing control unit and hydraulic unit [To the table](https://catalog.polo.blue/repair-manuals/brake-systems/45-anti-lock-brake-system/bosch-8-2i-9-0i-abs-edl-tcs-esp-rhd-vehicles/#6-4-5-installing-control-unit-and-hydraulic-unit)
| Part | Torque |
| --- | --- |
| Bolt for ABS hydraulic unit - N55- to bracket. | 8 Nm |
| Brake lines to ABS hydraulic unit - N55- Thread M10 x 1 | 14 Nm |
| Thread M12 x 1 | 14 Nm |

### [7.1 Removing and installing parts of ABS system on front axle](https://catalog.polo.blue/repair-manuals/brake-systems/45-anti-lock-brake-system/removing-and-installing-parts-of-abs-system-on-front-axle/index.md)

#### Torque
| Item | Part | Torque |
| --- | --- | --- |
| 2 | Hexagon socket head bolt | 8 Nm |
| 5 | Torx bolts | 12 Nm |
| 8 | Torx bolt | 4.5 Nm |

#### 7.1.1 Removing and installing speed sensor on front axle [To the steps](https://catalog.polo.blue/repair-manuals/brake-systems/45-anti-lock-brake-system/removing-and-installing-parts-of-abs-system-on-front-axle/#7-1-1-removing-and-installing-speed-sensor-on-front-axle)
| Step | Torque |
| --- | --- |
| Insert speed sensor into hole in wheel bearing housing and tighten bolt to 8 Nm. | 8 Nm |

### [7.2 Removing and installing parts of anti-lock brake system on rear axle (drum brakes)](https://catalog.polo.blue/repair-manuals/brake-systems/45-anti-lock-brake-system/removing-and-installing-abs-parts-rear-drum-brakes/index.md)

#### Torque
| Item | Part | Torque |
| --- | --- | --- |
| 2 | Hexagon socket head bolt | 8 Nm |
| 8 | Torx bolt | 4 Nm |

#### 7.2.1 Removing and installing speed sensor on rear axle (drum brakes) [To the steps](https://catalog.polo.blue/repair-manuals/brake-systems/45-anti-lock-brake-system/removing-and-installing-abs-parts-rear-drum-brakes/#7-2-1-removing-and-installing-speed-sensor-on-rear-axle-drum)
| Step | Torque |
| --- | --- |
| Insert speed sensor into hole in stub axle and tighten bolt to 8 Nm. | 8 Nm |

### [7.3 Removing and installing parts of anti-lock brake system on rear axle (disc brakes)](https://catalog.polo.blue/repair-manuals/brake-systems/45-anti-lock-brake-system/removing-and-installing-abs-parts-rear-disc-brakes/index.md)

#### Torque
| Item | Part | Torque |
| --- | --- | --- |
| 4 | Torx bolt | 4 Nm |
| 13 | Hexagon socket head bolt | 8 Nm |

#### 7.3.1 Removing and installing speed sensor on rear axle [To the steps](https://catalog.polo.blue/repair-manuals/brake-systems/45-anti-lock-brake-system/removing-and-installing-abs-parts-rear-disc-brakes/#7-3-1-removing-and-installing-speed-sensor-on-rear-axle)
| Step | Torque |
| --- | --- |
| Insert speed sensor into hole in stub axle and tighten bolt to 8 Nm. | 8 Nm |

## 46 – Brakes - mechanism

### [1.1 Repairing front brakes, FS III brake caliper](https://catalog.polo.blue/repair-manuals/brake-systems/46-brakes-mechanism/repairing-front-brakes-fs-iii-brake-caliper/index.md)

#### Torque
| Item | Part | Torque |
| --- | --- | --- |
| 2 | Torx bolt | 4.5 Nm |
| 5 | Guide pin | 30 Nm |
| 8 | Brake hose with banjo union and banjo bolt | 35 Nm |
| 10 | Torx bolts | 12 Nm |
| 14 | Hexagon socket head bolt | 8 Nm |

### [1.2 Removing and installing brake pads, brake caliper FS III](https://catalog.polo.blue/repair-manuals/brake-systems/46-brakes-mechanism/removing-and-installing-brake-pads-brake-caliper-fs-iii/index.md)

#### 1.2.2 Installing [To the steps](https://catalog.polo.blue/repair-manuals/brake-systems/46-brakes-mechanism/removing-and-installing-brake-pads-brake-caliper-fs-iii/#1-2-2-installing)
| Step | Torque |
| --- | --- |
| Guide pin to brake carrier | 30 Nm |

### [1.3 Removing and installing brake caliper FS III](https://catalog.polo.blue/repair-manuals/brake-systems/46-brakes-mechanism/removing-and-installing-brake-caliper-fs-iii/index.md)

#### 1.3.2 Installing [To the steps](https://catalog.polo.blue/repair-manuals/brake-systems/46-brakes-mechanism/removing-and-installing-brake-caliper-fs-iii/#1-3-2-installing)
| Step | Torque |
| --- | --- |
| Guide pin to brake carrier | 30 Nm |
| Brake hose to brake caliper | 35 Nm |

### [1.4 Repairing front brakes, FN 3 brake caliper](https://catalog.polo.blue/repair-manuals/brake-systems/46-brakes-mechanism/repairing-front-brakes-fn-3-brake-caliper/index.md)

#### Torque
| Item | Part | Torque | Notes |
| --- | --- | --- | --- |
| 1 | Torx bolts | 12 Nm |  |
| 3 | Torx bolt | 4.5 Nm |  |
| 8 | Guide pin | 30 Nm |  |
| 10 | Brake hose with banjo union and banjo bolt | 35 Nm |  |
| 11 | Guide pin | 30 Nm |  |
| 15 | Ribbed bolt | 124 Nm | Clean if reused. |
| 18 | Hexagon socket head bolt | 8 Nm |  |

### [1.5 Removing and installing brake pads, brake caliper FN 3](https://catalog.polo.blue/repair-manuals/brake-systems/46-brakes-mechanism/removing-and-installing-brake-pads-brake-caliper-fn-3/index.md)

#### 1.5.2 Installing [To the steps](https://catalog.polo.blue/repair-manuals/brake-systems/46-brakes-mechanism/removing-and-installing-brake-pads-brake-caliper-fn-3/#1-5-2-installing)
| Step | Torque |
| --- | --- |
| Guide pin to brake carrier | 30 Nm |

### [1.6 Removing and installing brake caliper FN 3](https://catalog.polo.blue/repair-manuals/brake-systems/46-brakes-mechanism/removing-and-installing-brake-caliper-fn-3/index.md)

#### 1.6.2 Installing [To the steps](https://catalog.polo.blue/repair-manuals/brake-systems/46-brakes-mechanism/removing-and-installing-brake-caliper-fn-3/#1-6-2-installing)
| Step | Torque |
| --- | --- |
| Guide pin to brake carrier | 30 Nm |
| Brake hose to brake caliper | 35 Nm |

### [2.1 Removing and installing rear brakes](https://catalog.polo.blue/repair-manuals/brake-systems/46-brakes-mechanism/removing-and-installing-rear-brakes/index.md)

#### Torque
| Item | Part | Torque |
| --- | --- | --- |
| 2 | Hexagon socket head bolt | 8 Nm |
| 4 | Brake line | 14 Nm |
| 8 | Torx bolt | 4 Nm |

### [2.3 Repairing rear brakes](https://catalog.polo.blue/repair-manuals/brake-systems/46-brakes-mechanism/repairing-rear-brakes/index.md)

#### Torque
| Item | Part | Torque |
| --- | --- | --- |
| 11 | Hexagon socket head bolt | 8 Nm |

### [3 Repairing rear brakes (disc brakes)](https://catalog.polo.blue/repair-manuals/brake-systems/46-brakes-mechanism/repairing-rear-brakes-disc-brakes/index.md)

#### Torque
| Item | Part | Torque | Notes |
| --- | --- | --- | --- |
| 1 | Torx bolt | 4 Nm |  |
| 7 | Hexagon socket head bolt,  and turn 30° further | 30 Nm |  |
| 8 | Brake hose | 38 Nm | With banjo bolt and seals · Specified torque of banjo bolt to brake caliper · Do not disconnect brake hose when changing pads. |
| 9 | Self-locking hexagon bolt | 35 Nm | Always renew after removing. |

### [3.1 Removing and installing brake pads/linings](https://catalog.polo.blue/repair-manuals/brake-systems/46-brakes-mechanism/removing-and-installing-brake-pads-linings/index.md)

#### 3.1.2 Installing [To the steps](https://catalog.polo.blue/repair-manuals/brake-systems/46-brakes-mechanism/removing-and-installing-brake-pads-linings/#3-1-2-installing)
| Step | Torque |
| --- | --- |
| Hexagon bolt, brake caliper to brake carrier 35 Nm | 35 Nm |

### [3.2 Removing and installing brake caliper](https://catalog.polo.blue/repair-manuals/brake-systems/46-brakes-mechanism/removing-and-installing-brake-caliper/index.md)

#### 3.2.2 Installing [To the steps](https://catalog.polo.blue/repair-manuals/brake-systems/46-brakes-mechanism/removing-and-installing-brake-caliper/#3-2-2-installing)
| Step | Torque |
| --- | --- |
| Hexagon bolt, brake caliper to brake carrier 35 Nm | 35 Nm |
| Brake hose to brake caliper | 38 Nm |

### [4 Assembly overview – handbrake lever](https://catalog.polo.blue/repair-manuals/brake-systems/46-brakes-mechanism/assembly-overview-handbrake-lever/index.md)

#### Torque
| Item | Part | Torque |
| --- | --- | --- |
| 6 | Hexagon nut | 23 Nm |

### [5.1 Assembly overview – brake pedal, lefthand drive](https://catalog.polo.blue/repair-manuals/brake-systems/46-brakes-mechanism/assembly-overview-brake-pedal-lefthand-drive/index.md)

#### Torque
| Item | Part | Torque | Notes |
| --- | --- | --- | --- |
| 2 | Self-locking hexagon nut | 25 Nm | Always renew after removing. |

### [5.2 Assembly overview – brake pedal, right-hand drive](https://catalog.polo.blue/repair-manuals/brake-systems/46-brakes-mechanism/assembly-overview-brake-pedal-right-hand-drive/index.md)

#### Torque
**All items:** Always renew after removing.

| Item | Part | Torque |
| --- | --- | --- |
| 5 | Nut | 25 Nm |
| 6 | Nut | 25 Nm |

#### 5.2.4 Installing pedal cluster [To the table](https://catalog.polo.blue/repair-manuals/brake-systems/46-brakes-mechanism/assembly-overview-brake-pedal-right-hand-drive/#5-2-4-installing-pedal-cluster)
| Part | Torque |
| --- | --- |
| Pedal cluster to brake booster and plenum chamber bulkhead ♦Use new nuts | 25 Nm |
| Foot support cover to plenum chamber bulkhead | 5 Nm |

#### 5.2.6 Installing brake pedal [To the table](https://catalog.polo.blue/repair-manuals/brake-systems/46-brakes-mechanism/assembly-overview-brake-pedal-right-hand-drive/#5-2-6-installing-brake-pedal)
| Part | Torque |
| --- | --- |
| Brake pedal to pedal cluster ♦Use new nuts | 25 Nm |
| Pedal cluster to brake booster and plenum chamber bulkhead ♦Use new nuts | 25 Nm |

## 47 – Brakes - hydraulics

### [1.1 Repairing FS III brake calipers](https://catalog.polo.blue/repair-manuals/brake-systems/47-brakes-hydraulics/repairing-fs-iii-brake-calipers/index.md)

#### Torque
| Item | Part | Torque | Notes |
| --- | --- | --- | --- |
| 2 | Bleeder valve | 10 Nm | Apply thin coat of assembly paste G 052 150 A2 to thread before screwing in. |
| 4 | Guide pin | 30 Nm |  |

### [1.3 Repairing FN 3 brake calipers](https://catalog.polo.blue/repair-manuals/brake-systems/47-brakes-hydraulics/repairing-fn-3-brake-calipers/index.md)

#### Torque [To the drawing](https://catalog.polo.blue/repair-manuals/brake-systems/47-brakes-hydraulics/repairing-fn-3-brake-calipers/#t109-562)
| Item | Part | Torque | Notes |
| --- | --- | --- | --- |
| 2 | Bleeder valve | 10 Nm | Before screwing in, apply thin coat of assembly paste - G 052 150 A2- to thread. |
| 4 | Guide pin | 30 Nm |  |

### [2 Repairing rear brake calipers](https://catalog.polo.blue/repair-manuals/brake-systems/47-brakes-hydraulics/repairing-rear-brake-calipers/index.md)

#### Torque [To the drawing](https://catalog.polo.blue/repair-manuals/brake-systems/47-brakes-hydraulics/repairing-rear-brake-calipers/#t114-89)
| Item | Part | Torque | Notes |
| --- | --- | --- | --- |
| 1 | Self-locking hexagon bolt | 35 Nm | Renew. · When loosening and tightening, counterhold on guide pin. |

### [5.1 Assembly overview – brake booster/brake master cylinder (left-hand drive vehicle)](https://catalog.polo.blue/repair-manuals/brake-systems/47-brakes-hydraulics/assembly-overview-brake-booster-master-cylinder-lhd/index.md)

#### Torque
**All except 11:** Always renew after removing.

| Item | Part | Torque |
| --- | --- | --- |
| 7 | Self-locking hexagon nut | 25 Nm |
| 11 | Torx bolt | 7 Nm |
| 12 | Self-locking hexagon nut | 25 Nm |

### [5.2 Assembly overview – brake booster/brake master cylinder (right-hand drive vehicle)](https://catalog.polo.blue/repair-manuals/brake-systems/47-brakes-hydraulics/assembly-overview-brake-booster-master-cylinder-rhd/index.md)

#### Torque
| Item | Part | Torque | Notes |
| --- | --- | --- | --- |
| 4 | Self-locking hexagon nut | 25 Nm | Qty. 4 · Always renew after removing. |
| 8 | Bolt | 7 Nm |  |
| 10 | Nut | 25 Nm |  |
| 16 | Bolt | 4 Nm |  |

### [5.6 Vacuum pump for brakes V192](https://catalog.polo.blue/repair-manuals/brake-systems/47-brakes-hydraulics/vacuum-pump-for-brakes-v192/index.md)

#### 5.6.1 Assembly overview - vacuum pump for brakes - V192- [To the drawing](https://catalog.polo.blue/repair-manuals/brake-systems/47-brakes-hydraulics/vacuum-pump-for-brakes-v192/#5-6-1-assembly-overview-vacuum-pump-for-brakes-v192)
| Item | Part | Torque | Notes |
| --- | --- | --- | --- |
| 1 | Bolt | 8 Nm | Qty. 2 |
| 7 | Bolt | 25 Nm | Qty. 3 |

#### 5.6.3 Installing [To the table](https://catalog.polo.blue/repair-manuals/brake-systems/47-brakes-hydraulics/vacuum-pump-for-brakes-v192/#5-6-3-installing)
| Part | Torque |
| --- | --- |
| Vacuum pump for brakes - V192- to bracket | 8 Nm |

### [5.8 Removing and installing brake light switch F, left-hand drive](https://catalog.polo.blue/repair-manuals/brake-systems/47-brakes-hydraulics/removing-and-installing-brake-light-switch-f-left-hand-drive/index.md)

#### In the steps
| Step | Torque |
| --- | --- |
| Torx bolt to brake master cylinder | 7 Nm |

### [5.9 Removing and installing brake light switch F, right-hand drive](https://catalog.polo.blue/repair-manuals/brake-systems/47-brakes-hydraulics/removing-and-installing-brake-light-switch-f-rhd/index.md)

#### Torque
| Part | Torque |
| --- | --- |
| Brake light switch - F- to brake master cylinder | 7 Nm |

### [6.1 Removing and installing brake master cylinder, left-hand drive](https://catalog.polo.blue/repair-manuals/brake-systems/47-brakes-hydraulics/removing-and-installing-brake-master-cylinder-lhd/index.md)

#### 6.1.2 Installing [To the steps](https://catalog.polo.blue/repair-manuals/brake-systems/47-brakes-hydraulics/removing-and-installing-brake-master-cylinder-lhd/#6-1-2-installing)
| Step | Torque |
| --- | --- |
| Brake master cylinder to brake booster | 25 Nm |
| Brake lines to brake master cylinder | 14 Nm |
| Torx bolt for brake light switch to brake master cyl‐ 7 Nm inder | 7 Nm |

### [6.2 Removing and installing brake master cylinder, right-hand drive vehicle](https://catalog.polo.blue/repair-manuals/brake-systems/47-brakes-hydraulics/removing-and-installing-brake-master-cylinder-rhd/index.md)

#### 6.2.2 Installing [To the table](https://catalog.polo.blue/repair-manuals/brake-systems/47-brakes-hydraulics/removing-and-installing-brake-master-cylinder-rhd/#6-2-2-installing)
| Part | Torque |
| --- | --- |
| Brake master cylinder to brake booster | 25 Nm |
| Brake lines to brake master cylinder | 14 Nm |
| Brake fluid reservoir to brake master cylinder | 4 Nm |
| Brake light switch to brake master cylinder | 7 Nm |
| Coolant expansion tank to body | 5 Nm |

### [7.1 Removing and installing brake booster, left-hand drive](https://catalog.polo.blue/repair-manuals/brake-systems/47-brakes-hydraulics/removing-and-installing-brake-booster-left-hand-drive/index.md)

#### 7.1.2 Installing [To the steps](https://catalog.polo.blue/repair-manuals/brake-systems/47-brakes-hydraulics/removing-and-installing-brake-booster-left-hand-drive/#7-1-2-installing)
| Step | Torque |
| --- | --- |
| Brake booster to pedal cluster and plenum chamber 25 Nm bulkhead | 25 Nm |
| Brake master cylinder to brake booster | 25 Nm |
| Brake lines to brake master cylinder | 14 Nm |

### [7.2 Removing and installing brake booster, right-hand drive vehicle](https://catalog.polo.blue/repair-manuals/brake-systems/47-brakes-hydraulics/removing-and-installing-brake-booster-rhd/index.md)

#### 7.2.2 Installing [To the table](https://catalog.polo.blue/repair-manuals/brake-systems/47-brakes-hydraulics/removing-and-installing-brake-booster-rhd/#7-2-2-installing)
| Part | Torque |
| --- | --- |
| Brake booster to pedal cluster and plenum chamber bulkhead ♦Use new nuts | 25 Nm |
| Brake master cylinder to brake booster ♦Use new nuts | 25 Nm |
| Brake lines to brake master cylinder | 14 Nm |
| Brake fluid reservoir to brake master cylinder | 4 Nm |
| Coolant expansion tank to body | 5 Nm |
