# 6.1 Removing and installing brake master cylinder, left-hand drive – Brake systems

> Removing and installing brake master cylinder, LHD on the VW Polo 6R: 17 steps, special tool VAS 5234, tightening torques and 4 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/brake-systems/47-brakes-hydraulics/removing-and-installing-brake-master-cylinder-lhd/
- Original document: https://cdn.polo.blue/files/vw-polo-5-2010-brake-systems-eng.pdf
- 47 – Brakes - hydraulics, [Brake systems](https://catalog.polo.blue/repair-manuals/brake-systems/index.md)
- Previous procedure: [5.9 Removing and installing brake light switch F, right-hand drive](https://catalog.polo.blue/repair-manuals/brake-systems/47-brakes-hydraulics/removing-and-installing-brake-light-switch-f-rhd/index.md)
- Next procedure: [6.2 Removing and installing brake master cylinder, right-hand drive vehicle](https://catalog.polo.blue/repair-manuals/brake-systems/47-brakes-hydraulics/removing-and-installing-brake-master-cylinder-rhd/index.md)

Special tools and workshop equipment required

![](https://catalog.polo.blue/manuals/vw-polo-2010-brake-systems/ec821d13d0ebab45.webp)

- Brake filling and bleeding equipment - VAS 5234-

![](https://catalog.polo.blue/manuals/vw-polo-2010-brake-systems/35d6d5ff8c7dae62.webp)

- Torque wrench - V.A.G 1331-

## 6.1.1 Removing

- Note or request radio code on vehicles with coded radio if necessary.
- Disconnect battery. ⇒ Electrical system; Rep. gr. 27; Disconnecting and reconnecting battery.

![](https://catalog.polo.blue/manuals/vw-polo-2010-brake-systems/2534a2a67984f1d5.webp)

- Remove air filter housing (except 4-cylinder injection engine, 1.4 l).
- Disconnect connector -A- from brake fluid level warning contact - F34-.
- Separate connector -C- from brake light switch - F-.
- Place sufficient lint-free cloths in area of engine and gearbox.
- Draw off as much brake fluid as possible from brake fluid reservoir using brake filling and bleeding equipment - VAS 5234- or extraction unit -V.A.G 1869/4-.

Additional work for vehicles with manual gearbox:

- Detach supply hose -B- for clutch master cylinder, lift clear and tie in place, or clamp off supply hose -B- for clutch master cylinder with a commercially available tool, e.g. Hazet 4590, and then pull off.

Continuation for all models:

- Push brake fluid reservoir pin through fastening tab and brake master cylinder.
- Then pull brake fluid reservoir out of brake master cylinder.

![](https://catalog.polo.blue/manuals/vw-polo-2010-brake-systems/4201994b193c446d.webp)

- Mark and unscrew brake lines from brake master cylinder -1- and immediately seal brake lines with plugs from repair kit Part No. 1H0 698 311 A.
- Remove nuts -2- from brake master cylinder.
- Carefully take brake master cylinder out of brake booster.
- Remove brake light switch - F-.

## 6.1.2 Installing

- Install in reverse order.

Observe the following important points when installing:

- When assembling brake master cylinder with brake booster, make sure plunger rod is properly positioned in brake master cylinder.
- Bleed brake system [⇒ 4 Bleeding brake system](https://catalog.polo.blue/repair-manuals/brake-systems/47-brakes-hydraulics/bleeding-brake-system/#t118-89).

Specified torques:

Brake master cylinder to brake booster

25 Nm

- Use new nuts!

Brake lines to brake master cylinder

14 Nm

Torx bolt for brake light switch to brake master cyl‐ 7 Nm inder

## Tightening torques on this page

### 6.1.2 Installing [To the steps](https://catalog.polo.blue/repair-manuals/brake-systems/47-brakes-hydraulics/removing-and-installing-brake-master-cylinder-lhd/#6-1-2-installing)
| Step | Torque |
| --- | --- |
| Brake master cylinder to brake booster | 25 Nm |
| Brake lines to brake master cylinder | 14 Nm |
| Torx bolt for brake light switch to brake master cyl‐ 7 Nm inder | 7 Nm |
