# 7.3 Removing and installing parts of anti-lock brake system on rear axle (disc brakes) – Brake systems

> VW Polo 6R, step by step: removing and installing rear ABS parts (disc brakes) – 7 steps, tightening torques and 3 drawings.

- Web page: https://catalog.polo.blue/repair-manuals/brake-systems/45-anti-lock-brake-system/removing-and-installing-abs-parts-rear-disc-brakes/
- Original document: https://cdn.polo.blue/files/vw-polo-5-2010-brake-systems-eng.pdf
- 45 – Anti-lock brake system, [Brake systems](https://catalog.polo.blue/repair-manuals/brake-systems/index.md)
- Previous procedure: [7.2 Removing and installing parts of anti-lock brake system on rear axle (drum brakes)](https://catalog.polo.blue/repair-manuals/brake-systems/45-anti-lock-brake-system/removing-and-installing-abs-parts-rear-drum-brakes/index.md)
- Next procedure: [8 Removing and installing parts of ESP system](https://catalog.polo.blue/repair-manuals/brake-systems/45-anti-lock-brake-system/removing-and-installing-parts-of-esp-system/index.md)

![](https://catalog.polo.blue/manuals/vw-polo-2010-brake-systems/61ba905cb6b4e685.webp)

- **1** Rear axle beam
- **2** Brake line
- **3** Handbrake cable
- **4** Torx bolt, 4 Nm
- **5** Brake disc
- **6** Cap
  - Pressing off and driving in ⇒ Running gear, axles, steering; Rep. gr. 42; Assembly overview: wheel bearings, disc brakes.
- **7** 12-point nut (self-locking)
  - Renew each time after removal ⇒ Running gear, axles, steering; Rep. gr. 42; Assembly overview: wheel bearings, disc brakes.
- **8** Wheel hub with wheel bearing
  - ABS sensor ring is installed in wheel bearing [⇒ 7.3 Removing and installing parts of anti-lock brake system on rear axle (disc brakes)](https://catalog.polo.blue/repair-manuals/brake-systems/45-anti-lock-brake-system/removing-and-installing-abs-parts-rear-disc-brakes/#t64-630).
  - Removing and installing ⇒ Running gear, axles, steering; Rep. gr. 42; Assembly overview: wheel bearings, disc brakes.
- **9** Hexagon bolt
  - Specified torque ⇒ Running gear, axles, steering; Rep. gr. 42; Assembly overview: wheel bearings, disc brakes.
- **10** Splash plate
- **11** Stub axle
- **12** ABS speed sensor
  - Before inserting sensor, clean hole inner surface and coat with high-temperature paste G 052 112 A3.
  - Removing and installing [⇒ 7.3.1 Removing and installing speed sensor on rear axle](https://catalog.polo.blue/repair-manuals/brake-systems/45-anti-lock-brake-system/removing-and-installing-abs-parts-rear-disc-brakes/#t65-82).
- **13** Hexagon socket head bolt, 8 Nm 

![](https://catalog.polo.blue/manuals/vw-polo-2010-brake-systems/3a2e4e8f2fa99eea.webp)

**ABS sensor ring -1- **

## 7.3.1 Removing and installing speed sensor on rear axle

Removing:

- Raise vehicle.

![](https://catalog.polo.blue/manuals/vw-polo-2010-brake-systems/a94b49363d4953ee.webp)

- Separate connector -1- from speed sensor wire and from speed sensor.
- Remove bolt -2- from stub axle.
- Pull ABS speed sensor out of stub axle.

Installing:

- Before inserting speed sensor, clean hole inner surface and coat speed sensor all-round with high-temperature paste G 052 112 A3.
- Insert speed sensor into hole in stub axle and tighten bolt to 8 Nm.
- Connect speed sensor to speed sensor wire.

## Tightening torques on this page

### Torque
| Item | Part | Torque |
| --- | --- | --- |
| 4 | Torx bolt | 4 Nm |
| 13 | Hexagon socket head bolt | 8 Nm |

### 7.3.1 Removing and installing speed sensor on rear axle [To the steps](https://catalog.polo.blue/repair-manuals/brake-systems/45-anti-lock-brake-system/removing-and-installing-abs-parts-rear-disc-brakes/#7-3-1-removing-and-installing-speed-sensor-on-rear-axle)
| Step | Torque |
| --- | --- |
| Insert speed sensor into hole in stub axle and tighten bolt to 8 Nm. | 8 Nm |
